Jeep Enthusiast Forums banner

What did you do to your XJ/MJ today?

4602123 Views 93880 Replies 2569 Participants Last post by  pdcomm
seriously, one of these threads needs to stay alive in the XJ/MJ section and what better time to get a real one going then now with the creation of the XJ/MJ GD. now, lets keep this going.

for me, all i did today was take pictures of my newly cut front bumper.

picture a few posts down.
  • Like
Reactions: 1
1 - 20 of 93881 Posts
It's sitting 20ft behind me getting the Saftey and Emissions test, Radiator flushed, Oil changed, Diff fluid Changed, Wiperblades Replaced, Replacing the P/S window regulator , and replacing all the U-joints on the Drive Shafts.
I just put $50.00 into the gas tank !
I had fixed the lock on the rear hatch of my XJ , An discovered the Previous Owner's special home brew insulation (Foam from a couch cushion) That he stuffed the hatch with which was the reason the lock didnt work ( Rods were disconnected) . An most importantly I had put my Jeepforum decal on the rear widow !
Today I had washed, An waxed the XJ. Lubed up all of the grease fittings, An hinges, Rotated the tires, Adjusted the tire pressure.
I had washed off all on the road salt, An waxed it ! Just so I can do it again next week after it snows again :thumbdown:

I also ordered my IRO Double Shear ADJ Trac bar, RE 3.5" leafs,and U bolts ! So My new lift kit I am piecing together will be complete in January after I order a set of Bilstein 5100's :2thumbsup:
Took it wheeling at 5 mile pass. For the first time, My wife did a little time in the drivers seat she did great for her first time behind the wheel.
Durt_Diver said:
constrictor? thats a fun trail. i hope you tried waynes world
Nope just rattlesnake. Once I get sliders lockers and highsteer ill do constrictor and waynesworld
I didn't do anything to my XJ today, However I did turn my Daily Driver into a XJ Part Hauler , RE 3.5" Leafs and Re ADJ Tracbar on thier way home from work with me !

Little Jeeper Approved Yet Again !

Here's my Pile of Parts sofar :

I wish I would have learned to piece together lifts a long time ago ! I'm 375.00 into my Re 3.5" Lift.
See less See more
I had finally got around to installing my AutoPal E Codes and Putco H4 harness today.
Sorry for the poor quality pics I had took them with my cellphone

Low Beam :

High Beam:

Low Beam:

High Beam:

Low Beam:

High Beam
See less See more
RMC_xj said:
Picked up my RigidCo FbG front bumper last week. Man, that thing is SWEET. Can't wait to get it on the jeep!
Make sure you take pics . Terrys fab work is top knotch. I'm ordering some sliders from him this week for my xj
I had ordered my Rigid rock sliders today. Terry is a great guy to deal with.

See less See more
99goldxj said:
The actually headlight install isn't what I am worried about, the wiring harness is though.
I installed the harness and h4 in my xj last sunday. It's a piece of cake. It should take you less than an hr from start to finish
I thought about washing/waxing it, But I remembered it is supposed to snow tomorrow .
I picked up my rigid rock sliders today. Terry is a great guy to deal with.


See less See more
I painted my Rigidco R22X Rocksliders

Pic's are in my Build thread
I finished collecting all of the parts for my new lift !

See less See more
How tall are you going?
I will be staying fairly low at 3.5" if you ready my build thread I have all of the details of my plans in the first post !
Bought it a 2 car Garage with an Attached house :2thumbsup:
I installed my New wheels pics are in my Build thread
I did a few thing today.

1. Ran a new ground to my head-unit so it would get power again.
2. Ran new speaker wires through the boots in the door jams, Spliced them into the factory Speaker wires behind the kick panels . Now I have 4 working speakers :duhrock: .
3. Washed the XJ to rid it of all of the road salt.
1 - 20 of 93881 Posts