Search Results for ‘wheel bearing’

Singapore Jeep dealer wants $1400 for parts alone! Front Wheel Bearings anyone? LOL MK Compass 2007 A front wheel bearing cost around $10ish in many cases, and original Mopar can be found under $40, albeit there are many counterfeits lurking around. The jeep dealer in Singapore wants over...

Searched and couldn't find anything exactly that is happening to me so I apologize if there is something already out there on this. So, this past weekend I went into my 2011 JKU Dana30 and did the maintenance on my front axle. I replaced Both U-Joints, Wheel Bearings(With new speed sensors)...

I'd like to get advice from you guys before I waste any money on replacing good parts. The car is an 02 WJ Overland with 190,000 miles on her. The link to it is in my signature below. Here's the issue: There is a rub-rub-rub noise above about 25 mph that sounds like a failed wheel bearing...

I've just bought a 2000 Cherokee sport for my daily driver, and it needed a wheel bearing on the driver side. No big deal, I've done that before. The problem is that the noise is still there with a new wheel bearing. While driving, when I curve left the sound goes away. When I curve right...

Okay, here's the scoop. 98 Cherokee, with a Chrysler rear end. Someone posted that if you have ABS its a Dana. I have ABS and have a Chrysler Rear end based on the pic posted in another post: http://www.jeepforum.com/forum/f11/identify-rear-axle-d35-chrysler-638105/ I am getting a...

My xj has a strange noise coming from the front left. My brake pads have alot of pad left on them, yet sometimes when I depress the brake pedal it does squeak. And most times just rolling around town, it squeaks with depressing any pedals other than the gas pedal. I thought it was a u joint, but...

Here's the newest of my how-to vids. I broke it up into three segments since the entire video is over 100 minutes long! This is very detailed, and designed to help a novice shadetree mechanic learn to perform this (all so common) service on a ZJ. Enjoy! My next video will be how to...

I have a 94 wrangler se i just got done replacing the front hub assemblies and u joints as well as the rear drive shaft u joints. i'm now moved to the back end and i need to replace the bearings but, i can't identify how to remove the axels. i have never dealt with a locker before do they have c...

I have a clunking noise coming from the driver side rear tire. It was most noticeable when coasting but not accelerating. I could move the tire side to side and hear the clunk. I thought it was the wheel bearing causing the noise. I had the bearing and retainer ring replaced. I also replaced the...

I just rotated my tires (5 tire rotation), and Now I hear a wah wah wah with a vibration coming from the rear of the vehicle, but only at +60 mph. There is about a 1 second pause between the wah's. I for sure feel it when on the accelorator or holding constant speed. If I speed up to 70 mph and...

So i recently upgraded from 31's which measure 29" to true 33 MT's which measure 33's on my 97 Sahara. Problem is as soon as i drove out of the shop after mount and balancing the new tires a screaching noise was coming from the front left brake dust cover. I pulled over and bent it back some and...

I've completely rebuilt the front end on my 83 CJ-7 (just because it needed it, not to attempt to fix this problem) - had it to the alignment shop - everything is good. I get a slight wobble above 50 MPH - it can be seen and heard. The rims were checked when I had the tires put on (31 X 10.50)...

OK so i'm a little confused on this. Internet sources tell me SKF BR10 or Timken U399 are the ones to get. Got some SKF BR10s and the thing looks like a unit bearing. That is, i cannot remove the bearing race, which i was going to install into the housing. My question is ... if i press the...

I'm replacing the U-joints in my front axle... got the passenger side done without any problems but now on the driver side I can't get the hub off the knuckle. I've been soaking it with WD-40 and banging around edge with a hammer and screwdriver for a while but still nothing. Even managed to...

I think this is the answer to my control problems. The track bar is loose on the lower end. Also, the rear wheel bearings must be bad (I can move the wheels back and forth with the jeep resting on all four). If I replace the bushing in the lower end of the track bar, will that tighten it up...