Search Results for ‘tub’

Hopefully I'll still be driving Jeeps by the time I could afford a project like this... I have a vision of a transparent jeep. Most of the time it's just the tub and top that are clear, all the internals probably need to be made of whatever they're made of for stress and thermal reasons. It's...

Deleted

Starting in about a week I am planning to dissemble my 94 YJ and pull the tub off the frame. My plan is to clean up the frame and use chassis saver to seal it. Additionally I plan to bed line the bottom and the inside of the tub. For anyone who has pulled the tub off their frame before is there...

Noobie jeep mechanic here with a problem on my 89 YJ with a 4.2. I'm trying to get off the tub so I can get the floors welded but there's some wires going through the fire wall that used to connect to the heating unit ecu thingy and I can't get them out. Photos will be attached below any advice...

Hey Guys, I have a 2004 TJ that's spent it's life in the north. Over the last few years a rust spot's been developing on the tub just under/behind the driver door, never paid much attention to it but lately its been getting pretty bad. Today I was looking at it closely to see what I can do...

Unfortunately, clean rust free tubs are not easy to fine in the South East... so I located a very nice tub in AZ. any suggestions on having it shipped back East? Thanks in advance for your help! Saving one CJ at a time!

I bought an 1981 half a year ago. The previous owner installed a new tub and in that process he also installed some non original used seats (not nice at all), but he provided me the original seats. I've been restoring them and now I need to install them. Unfortunately I cannot find the required...

I'm looking to clean out the inside of my YJ, anyone have any suggestions on how to go about doing this? All I can think of is to remove the seats and drain plugs and to get in there with some soap, brushes, and a hose. Thanks in advance.

i loss control of my jeep the other day and ran into a pine tree it bent the chorme bumper into a 90 degree angle and went straight into the fender and landed on the wheel the passenger fender is completely shot. chrome grille is bent about 2 inches in onthat side and caused the fan to go into...

okay guys as you can see from the pictures i have a serious issue. picture one and two are the center mount on the driver side. it is completely rusted through. picture three is the rear one on the drivers side which is continually getting worse. picture four is the middle on the passenger and...

Hey, rusted body mounts, (two right through). Looking to have some plates welded as a fix but it sounds like it may be better to replace the tub. Anyone got some advice on this? Also, I'm wondering if anyone can steer me to a decent guide on how to remove the tub? Where are the worst spots...

I was thinking about Plasti Dipping the inside of my tub for noise and to get rid of some rust that is under front side floorboards....has anyone tried this? If so how did it turn out??

All, I've got some pretty rough rear tub mounts on my 80 CJ-7 (imagine that). I'm trying to figure out how to tackle them - I know I'll probably have to replace the channels where they attach to the floor, but I can't seem to find those channels for sale anywhere - anyone have tips? Also, in...

hey guys sooo i rolled my tj :thumbdown: (frame seams straight but body is trashed) and found an 03 tub for cheap i was wondering if this would work or what problems i might run in to? i want to keep all the guts and my 4inch longarm lift will this tub still bolt into place?

So I am pretty new to the forum and even more new to actually owning a Jeep to work on. The Jeep is an 1981 CJ7 that is honestly above my head which has given me both some hesitation and some drive. The hesitation is that I should have purchased a little less of a project and the drive is...

hi, i have a 03 tj, 141,000km on her but the tub is starting to rot just below the licence plate.. was wondering if this is a normal tj thing or if i should be looking into this rot further :( i will end up fixing it but just looking to see what other people have done to either prevent the rot...

I was wondering if people had any advice for how to best approach the kind of rot/damage that I've got on the bottom of my tub. I'd love to go fiberglass but at the moment my budget won't have it so I've got to make this tub last. Since a picture is worth a 1000 words here are a few pictures...

I'm thinking about finally spraying my 97 TJ's tub with Raptor Line and as I started to pull up some of the carpet I noticed an upward dent above the left rear tire. This probably was happened when I blew out my stock rear end but I haven't noticed it before. Everything works fine so I'm not...