Search Results for ‘transfer case’

My Overland is giving the service 4wd/traction control light. I’ve read a few threads and decided to change out the ELSD motor but to not avail. The problem was intermittent but now they’re both on full time. From what I’m reading it’s either the DCM or lose wiring? Has anyone else had this...

I need to get a new transfer case. Long shaft or short? Says both will fit, but I suspected one was for auto and one for manual. One note on here says long shaft for manual Is that the correct answer. Not looking to remove it all right now just to look at it. Thanks in advance

Hello I'm looking to buy a np242j off of a 1993 early 94 build with the old gear cut. Current 249 vc is out and binding on pavement.

My buddy owns a 99 XJ. On the way back from work the transfer case blew up. He’s got a 231J and the prices are pretty high compared to what he can afford. Car lots around us have 0 Cherokees to pull from. They have grand Cherokees but he’d have to buy the drive shaft as well to do the...

Hey I just replaced the transmission on my 96 zj 4x4 and now it won’t move I know the fluid is good but when I put it in any gear the transfer case starts making noise when I give it gas and when I go back to park it makes a loud grinding noise any help appreciate

Just replaced the transmission on my 96 zj 4x4 and won’t move I know the fluid level is good when you put it in gear the transfer case starts making noise and when you go back to park it makes a horrible noise any help appreciate

I removed the cover on my Dana 300 transfer case to change the gasket. I found these two rings in the pan... I'm no transfer case expert but I don't think it came this way. Hah. What are they, where do they go and should I be sh!ting my pants because they are not where they belong?

I know some CJ-7's had "Quarda-trac". But are there later model systems that are a good swap into CJ's? All the options! Is there a reason why I never hear of anyone swapping these into CJ's?? 1 Command-Trac 1.1 Command-Trac 1.2 Command-Trac II 2 Rock-Trac 3...

I own a '06 TJ, 6 speed manual transmission. I had a SYE installed over a year ago and it fried something in my TC. I will need a replacement. To have a shop rebuild a new TC with a SYE will cost me a lot. Quadratec.com sells TCs with SYE kit already installed but only ones that fit the AX-15...

Hey there so i am in the process of swapping my 242 transfer case for a 249..at this point i have removed the 242 from my jeep ( 1996 Grand cherokee)...and have removed all bolts and started to separate the case to get the input shaft from it for the swap...my issue is the case is stuck upon...

VIDEO OF THE NOISE: Hey guys, I have 1977 Jeep CJ7 with a DANA 300 t-case and a T150 tranny. Just finished swapping in a 304 and took it out for a test drive and heard a grinding noise coming from what i thought was the tranny, so I changed the fluid and the noise went away in 2wd only, so I...

hello fellow jeepers!!! Does anybody can show me where should i start checking? and obviously give solutions Thanks in advance

I have a 1979 CJ7 304 (now a 360) 4SPD that is new to me and I need some input from the collective. The gap on these round bushings on the transmission mount don't look right. Is there a piece missing here, do I just crank on it until the bushings pinch the bracket? Also, I added a picture of...

My 4WD indicator was not working correctly so I replace the switch, it was bad and was stuck, but then I looked at the connector, it looked a bit green, so I sprayed it out and discovered two of the four pins where completely corroded and gone. Yippie. I cannot seem to find that connector...

I have a 1995 Jeep Grand Cherokee with the 5.2 and the 249 transfer case. I'm in the process of swapping in a 242 case, but I want to make sure I get the right donor. The case is dated July 1994. Can anyone tell me based of the attached picture if this is the old or new style gear cut? I've read...

Hi, This is actually my first post on the Jeep Forum. I am having an issue with my transfer case bushing. I was able to get the bushing onto the knob, but cannot get the ring over the plastic piece if that makes sense (excuse my lack of knowledge here). Any tips? I've attached a picture to...

All, I have a 97 Jeep Cherokee (XJ) 4.0L with 242K miles on it and it has a noise that I can't pinpoint. Before throwing time or money away, I thought I'd check the forum for insight or advice. All thoughts welcome. TC: NP231J Transmission: AW4 · The sound seems to come from...

Hey J33P P33PS. This forum has been really helpful, so in an effort to contribute towards the knowledge base, here is a documented explanation of how to fix this problem. If your 4WD shifter is loose, and/or stuck in 4WDH, 4WDL or 2WDH, it could be a few things. The best way to identify...

Hey everyone, I'm trying to track down an issue that I ran into over the weekend. I was taking my 5.7 with QD2 up a light slope (cars going up and down it too) that was washboarded quite a bit. I hit one of the larger bumps and then began hearing a thunk that sounded like a bad U Joint or CV...

Hey guys, I’m new to the forum and this is my first post and was hoping for some expert help! I have a niner that I am getting ready to put a 231 into but have been having a hell of a time trying to find a 231 shift bezel to complete the look. Anyone have any ideas where I could find one? I’ve...