Search Results for ‘tranfer case’

My WJ 4.0 with The over advanced Quadra drive system is making a rumbling or rubbing sound and it’s kinda loud when turning at slower speeds not always but pretty often and I suspect it coming from the T-Case as there was red fluid in it so I ordered the Mopar stuff and pumped most old fluid out...

I have an 01 and an 03 WJ. Both are I6. Inherited from my parents some time ago. I have been letting my kids drive the 03, but they have their own cars now. I plan on keeping the 01, lower mileage, better package, BB. It has the NV247 that I recently rebuilt, the 03 has the 242. I don't off...

Need some help diagnosing possible transmission issue Earlier today I was driving my jeep(2002 wrangler 4.0 I6 auto) down the highway at around 70mph when all of a sudden the revs went crazy high, when I let off the gas it went down to idle and when I started to apply gas again it acted like...

242HD transfer case, front and rear drive shafts, shifter bezel and new seals. Removed from an 03 WJ with the 4.7L. Located in Frackville, PA but willing to meet up to 4 hours one way. Asking $400 OBO.

So haven't had a chance to do a lot of poking around yet, but I've got some issues going on with my NP231. When I throw it into 4 hi, there is quite a bit of gear noise, driving down the road. A lot of metallic whining. When I first heard it, I put it back into 2wd, but the gear whine would not...

Need help, just got a 1989 cherokee and it's acting like it has a locker on the front end, when I make a turn my front wheel "hops" like I have it in 4x4 but it's in 2 hi, if anyone can tell me where the shift motor for the transfer case is located and what it looks like that'd help. Most of the...

I own and 2000 Grand Cherokee Laredo 4x4 automatic. It's currently put to rest because it's having some serious driving problems. What's going on is while driving for about 15 mins or so there starts a real bad grinding coming from the transmission/transfer. It slows dramatically and when it...

Howdy gents. I am knee deep in a 2.5 to 4.3 swap. I have the frame stripped and am to the point where I need to plan out my new drivetrain.:thumbsup: Found a drivetrain pulled out of a swapped YJ. Keeping the nv3500 tranny that came out of it. I am stuck on T-case choices. Do I try to make room...

With the front wheels jacked off the ground, if I spin the tires, there is a clunking coming from around where the front shaft meets the transfer case. It may be coming from the case itself, but the shaft itself has some spin play to it. I JUST replaced the u-joint on the driver side axle shaft...

this sounds like its coming from the bell housing but i wont be sure till i get the trans off. its a sporadic loud clang that only happens when its in gear. if its in neutral or the clutch is depressed it wont make noise, however, it will jusp outa gear. any thoughts on this? oh, one...

I have an 87 yj 4.2 L with the BA10/5 tranny and np 231 T-case. One day I was accelerating from a stop when the rear driveshaft broke lose and started violently thrashing. I immediately pulled over, and looked underneath to find it was bleeding t-case fluid everywhere. After closer inspection I...

Im in need of the spirial brake cone in the clutch pack in Borg Warner 1305/1339 Quadra Trac transfer cases. There are no parts avalible anywere I have found for these clutch packs.

So I guess this will be my first real right-up I have do that will HOPEFULLY provide some helpful info to everyone out there that has had enough with the complicated stock linkage or who has modified their drive line. Parts List: Will update as I go if needed 2 - 7/16" Ball joint rod ends -...

I recently bought a 2003 Rubicon over Autotrader. I was driving it home from Chicago to Nebraska when the transfer case blew. The Jeep is in Iowa at the repair shop of the guy who towed it. I have no idea if this person has any experience with Jeeps, or if he's compitent at all. He said that...

Im very new to the Jeep life style and loving it but...... I just had my first break down. My transfer case is finished 4X4 just grinds when engaged. I can clearly hear the chain just skipping and missing teeth. When I drained the oil out, it was very dark (black) and there was a lot of slop...

After using 4 lo when i went back into 2 wheel drive i could hear a clicking sound coming from the tcase. When i turn the wheel it still feels like its engaged in 4, I have tried several times to put it back in 2 wheel drive but i can still hear the noise. Maybe a linkage issue? Any help would...