Search Results for ‘seal’

Hi. My Jeep (bought new) needs a rear main seal I’m told. I was informed there wasn’t a way to know if it’s a one piece or two piece seal until into it. Also, I was told the motor had to be dropped. No one else on here has mentioned this, and I must admit, that makes me freak out. This all...

Hi, I have a 98 Tj Hard Top, and I can't seem to find the rubber seal that goes in the tailgate or trunk however you want to call it... Where can i find It, and that also ships interntionaly? Thanks

I've been searching for replacement seals for the ZJ as I am replacing the evap core and the heater core, but I've been having some trouble finding good information on the seals. The oem seals are obviously not offered anymore and I can't find aftermarket ones, so I am going to replace the seals...

I have just repaired the sun roof (leaked) and replaced the headliner. Now I need to replace the rubber seal around the sunroof glass and can't find any source. Can anyone help?

Hello everyone, I used a 3D printer to make a seal puller There is enough clearance to change the seal out without needing to pull out the other half of the axle, which lets you do it without having to take the hub apart and drain the oil Just thought I’d you all know that it IS possible

With the weather now cold I figured I would take the opportunity to replace my windshield, glass, seals, etc. Everything went together easily enough until I installed the cowl seal and tried to re-connect the roll bar. The thickness of the new seal made it impossible for me to connect the roll...

I've got a leak that I've been noticing more often over the past few weeks. From what I've researched it looks like it might be oil coming from the rear main seal, can anyone confirm this? It leaks about a drip every minute when I've just parked, but slows down pretty quickly when it cools...

Hello, i am replacing the seals around the bottoms of the windows on my jeep. Have been looking around for a tech on how exactly to do but have had no luck. Does anyone have advice on how to do this? :cheers2:

I recently purchased a used hardtop for my '97 TJ Sahara, but it came with just the top itself. There are no seals or anything to secure it to the jeep but the hooks in the front. So what do I need to make it complete/safe? Thanks in advance!

I did search on here but was suprised I could not find this. Looking for part numbers for the the seal between the transmission and transfer case. Plus the seal that is around the torque converter. Anyone know of a part number that will help out? It is a 1995 Cherokee sport, 6 cylinder, 4...

I'm replacing the axle seals on my D30. During the removal, I removed and cleaned out something that looks like a bead of RTV next to the seals (this picture is of some one else's, mine were gray and didn't look nearly as nice). See attached picture. Does anyone know the purpose of that RTV? Do...

Trying to get the floorboards dry in my 1994 Wrangler. I cleaned out the cowl drain and that didn't seem to help. I bought a new windshield seal and installed it ( here is a link to the install ) It wasn't too difficult but some of the bolts were rusted. They are all Torx fittings of various...

hey all I cannot seem for the life of me find some damn rear outer wheel bearings not sure which ones are right on rock auto, seems like they have "axle bearings " listed and wheel/hub bearings ? are these the correct bearing and seal #s? NATIONAL Part # 5707 and NATIONAL Part # 8660S ? thanx...

Hi guys, About a week ago I replaced the drive chain in my NP231 t-case (in a '96 XJ) and all seemed to go well. Yesterday though I noticed smoke coming from the undercarriage after driving it for several miles, and the smoke smelled like ATF. Looking underneath, I found that a HUGE amount of...

Hey all, I have read all the posts on doing this. The only thing the post doesn't specify is how hard the new seal is supposed to be to go in. I have a 2002 three speed auto jeep wrangler. I think I narrowed the tranny leak to the shift shaft. I did everything the posts I've read to a T...

Does anyone happen to know a source for the seal that sticks on the top of the condenser, my dealer cannot find a part number... Attached is an image of my condenser w/out the seal and what is left of the old seal in the foreground. Thanks.

The seal seems to have a "mouth" cut into it. Which side does this face (inside of engine or outside of engine)? And do you recommend RTV between the oil pan and the gasket? How about RTV between the gasket and the block?

5.2/46RH/249TC Has anyone replaced their seal and experienced the SAME amount of leakage? I realize I'll get flamed for going Napa and not Mopar, but it was all I had access to at the time. I'm willing to order a new one and get under there AGAIN, but only if it's going to fix what's going on...

So, since it is (finally) heating up here, I noticed that the AC on my '93 4.0 is, well... not. I searched the threads and found a few suggestions and after poking around some found that where the low side metal tube enters a coupling that passes through the firewall, it had popped out...

I need to change the seals for my disk brake calipers on the front. I tried carefully prying on them but that didn't work. I was thinking of hooking the calipers back up to the master cylinder and trying it that way. Anyone have any other easier ideas?