Search Results for ‘removal’

Restoring a CJ-7 where previous owner rhino lined the entire body. Any tips on what works best for removal? I haven’t found much about how to get it off the body. Will dipping work? Sandblasting? Or will it need to be heat gun and scraping?

Hello everyone, I used a 3D printer to make a seal puller There is enough clearance to change the seal out without needing to pull out the other half of the axle, which lets you do it without having to take the hub apart and drain the oil Just thought I’d you all know that it IS possible

Hey guys! I was thinking about removing the passenger seat when we had our newborns car seat rear-facing. Seems like this would make it a bit easier to put her in and really there isn't much room for a passenger if her car seat is in there. Does anyone see any problem with this? I plan to...

Starting in about a week I am planning to dissemble my 94 YJ and pull the tub off the frame. My plan is to clean up the frame and use chassis saver to seal it. Additionally I plan to bed line the bottom and the inside of the tub. For anyone who has pulled the tub off their frame before is there...

Hi All, I'm looking to remove the AC components on my 89 Cherokee (4.0L). The compressor is shot and I'd rather have the extra space under the hood (and less weight). I found this post for the idler pulley to replace the compressor in the serp belt loop: (link here-omitted due to first post)...

As I was removing the rear seat cover I ran across 4 metal rods that are stuck into the cushion that the cover is attached to. How do I go about getting the seat cover off of them?:confused:

I have a 1992 Jeep Wrangler YJ and the front seat belt is very worn and it is a safety concern, so I bought a new set. This is the belt that I bought (Omix-ADA Rugged Ridge Retractable 3 Point Seat Belt), so it is very similar to the stock one I'm taking out. I found some posts that said it...

Hey guys, I need some help figuring out how to remove the rear seats in my 2002 Jeep Wrangler SE. I have owned it for 3 or so years and never tried but I need some room to move some stuff and need them out. They are not original, the last owner installed them and they are Bestops. I have read...

Today I am going to tell you how to remove the door panels off of a 1998 TJ. There are many reasons why you may want to remove the door panels, but mine was so that I could paint them a different color. First you start off by removing the three screws around the bezel of the door frame. There...

I am new to the Forum so please excuse any mistakes. I am trying to repair my pastors Jeep Commander. He was told the front differential needed to be changed so in a effort to save him some money I offered to complete the repair. I have now came to the realization that this is a completely...

Hi, First time posting here. My dog chewed one of the rear side seat belts in my 2012 Sahara Unlimited and I was wondering if I could replace just the belt? If so, which OEM part number should I be looking for? Thanks, Frederick

Ok guys, I can't get my belt off to save my life. I've loosened everything, the nuts on the front of the power steering pump, the one on the back, and the adjustment nut below the pump, facing the air box. It won't budge. Maybe I'm missing something, but every write up is telling me the same...

Hello I recently bought a 1995 jeep grand cherokee laredo, from what I know it came with the OEM keyless entry. The guy who i bought it off of also put in a Nordic keyless entry. Now the OEM works fine but its only good for 3 feet and sometimes not even that, the Nordic one only starts the...

Hi everyone I am new to the forum world, figured i would give it a try seeing as how im hitting a wall on the internet searching... I guess you tube does NOT have everything. Im trying to remove the D35 rear axle on my 95 Jeep Cherokee and install the D35 from my 96 XJ. Should just be an easy...

Hey guys, I'm replacing the u-joint on my rear drive shaft. I've got both clips off the drive shaft but can seem to get the shaft out. You just push toward the transmission and the pull it back out once the back end falls out, right? Mine wont budge at all. Also, do I need to drain the...

So I began to disassemble my 1980 CJ7 this weekend, and for the life of me I cannot get the bolt out of the front spring rear mount. I am thinking its just rusted to the sleeve in the bushing, though half a can of liquid wrench had no effect. I am worried about "nudging" it too hard and bending...

Hey guys, picking up a new T176 tomorrow to replace mine while I attempt to rebuild it. I cant seem to find any good threads on the steps of removing the transmission. It will be a 1 man job so I will want to do it separately from the transfer case. I am guessing I need to removing the Dana 300...

I am currently in the process of replacing my stock steering shaft with an after market heavy duty steering shaft from Crown (Part #: 5354934HD). I have unbolted both the top and bottom ends of the old steering shaft, as seen here. The problem is I don't know whether I need a special tool to...

Just bought my first XJ, a couple days go. I love it already. I want to redo the trim front, rear, and doors. Ive seen some people have just removed the side trim all together, I just want it to have that new look. Any suggestions? Paints? Primers?

I have an 06 (wk) 3.7L and I need to know how to remove the headlight assemblies 9driver and passenger side) NOT just the bulb, the WHOLE headlight assembly. I bought aftermarket headlights with projectors that I want too install and I couldn't find anything here or in the manual on how to...