Search Results for ‘rear end’

Hey guys just bought this 91 XJ I think the guy said it came with a four and a half inch lift from rough country trying to figure out the rear end sag anybody help me out here? Thanks you in advance! Measurements - Center of tire to bottom of fender Passenger side Rear tire 21 and 1/8 Front...

I'm about to change the diff oil in a 06 WK with the 8.25 rear axle, I don't know how much it has been since the last change so I was thinking if it needs to be cleaned when I change the fluid. I have read on some forums people saying to use brake cleaner, but other people say no, don't use any...

I have 35's but want to get a upgraded rear end first. I was looking for used Dana 44 but can't find any locally. I found some 8.8's one geared 3.73 and one 4.10. My stock gears now are 3.73 front and rear. If I get the 4.10 would I have to re gear the front axle? Or should I get the 3.73 rear...

I just bought a 1990 Wrangler with a 4.2L and a 3spd auto I have got the engine running a lot better due to everyone's helpful knowledge here so here is the issue my jeep had started making a loud pop here and there that felt like it was right under me I thought maybe a ujoint was going bad...

ok im looking at a danna 44 from a willys jeep my question is it will it bolt right in my cj7 in place of the amc 20

[/URL][/IMG] [/URL][/IMG] I-77, just south of Charlotte. Got punted by a Mazda Truck. I have removed the ruined spare and rear tire carrier. While starting to tear it down to try and bang out the damage, I ran into a few snags. 1. Can I/how do I remove the rear bumper to "un-bend" it? While...

Hey, changed the fluid in my rear diff yesterday. When all the oil drained had drained there was a small piece of metal on the bottom of the diff. Turns out it's part of one of the retaining clips of the clutch pack. Spider gears as well as ring an pinion looked fine as far as I could see...

So Im a little confused and stumped. I have my stock d35 with a Aussie locker in and a 249 transfer case. when around town driving it seems normal i can feel the locker working and unlocking around tight turns. while out wheeling a couple weeks ago it just didn't perform like i had expected it...

Hi Fellow CJers, I grenaded the AMC 20 in my 84 CJ7. No I wasn’t on some crazy trail or remote desert location “Thank God” It was in the parking lot of my local Starbucks. I Know, Don’t say it, at Starbucks. As I understand it the Track Lok system is inherently prown to failure after years of...

I have a clunking noise coming from the driver side rear tire. It was most noticeable when coasting but not accelerating. I could move the tire side to side and hear the clunk. I thought it was the wheel bearing causing the noise. I had the bearing and retainer ring replaced. I also replaced the...

I am looking at a '99 wrangler that has a rear end from a '90 wrangler. Are there any problems with this? Can this damage the transmission?

I have a 1993 ZJ with the five speed manual and the I6, runs and drives great but there is a weird rubbing noise when I'm coasting. If I really step on it there is no noise but otherwise there is and it seems to go faster the faster I go. I had it on a lift and everything seems to have checked...

So awhile back I posted a post about converting an XJ D44 into a TJ D44. Funny enough once I got down there (I just got my Jeep a month or so ago and was told it was a D44 rear) I realized it was a D35. So after much splicing the XJ D44 fit like a beauty and it is a lot more enforced than my old...

I am putting in a XJ Dana-44 Limited Slip TruPosi 3.73 into my already Dana-44 3.73 (spyder gears) TJ and was just wondering if anyone knew if there was anything extra required or if that didn't work. Any help appreciated

I recently swapped the frame on my 99 sahara with the frame from a 4 cyl 05 tj. prior to the swap, my rear tires had plenty of clearance. after the swap, my right rear tire seems to be rubbing up against the part of the frame that holds the coil spring in place. the jeep is lifted 2.5" via...

I have a 99 sahara that i just replaced the frame on. the reason for the frame replacement was because of the amount of rot on the original frame. the rear upper control arms (both) rotted completely off and may have messed up my rear diff. i have a dana 35 in the rear. when i accelerate, i...

The rear differential on my 99 WJ is leaking. It looks like it's coming from the point where the axle tube meets the center casting. Any ideas why it would leak there? Do I need a whole new diff or is there a seal in there to replace?

The rear differential on my 99 WJ is leaking. It looks like it's coming from the point where the axle tube meets the center casting. Any ideas why it would leak there? Do I need a whole new diff or is there a seal in there to replace?

I am actually making my fuel release electric by hooking up a shaved door solenoid. I am looking for a 12volt power source in the rear so i don't have to run a lead all the way up to the engine bay. I've run my test light all around with no avail. any ideas?

Hey about a month ago i took my zj out to trails all weekend after that i took it agian in sugar sand and its like my rear end froze up it started shakin real bad vibrating and loud clunking noise, then after a few trys with exseleration it went back to normal and made it out (in 2 wheel) so i...