Search Results for ‘pitman arm’

Back in late August I was getting some really bad Death Wobble problems on my '03 TJ (4.5" lift and 35" tires if it matters) that I did not have the time to diagnose and fix. Eventually, I bit the bullet and brought the Jeep to a 4WD shop. They told me that my track bar and drag link needed to...

Lately I have been experiencing a loud pop when turning left or right. It is just one singular pop, I checked and everything is tight. When turning the wheel (and you are in the engine bay) the popping seems to be centered around the steering box, so it could be the pit man arm tie rod, or the...

I have about 6 in of lift and stock pitman arm do i need to get a longer arm? Steering is decent but would like to improve it being this is my daily driver. Any sugestions or what have yall done?

I put this under the jk section and got no responses so I'm gonna try here. last night I get to digging into a thread about straightening ur steering wheel and toe-in and alignment and camber. All that good stuff. So Me and a buddy get out today and are just messing around checking the stuff by...

So last night I get to digging into a thread about straightening ur steering wheel and toe-in and alignment and camber. All that good stuff. So Me and a buddy get out today and are just messing around checking the stuff by the write up I read. First off I guess it's my fault for not checking...

Hey guys my pitman arm looks loose and I have terrible wheel slop where I can't move the wheel and it has about 1/2 inch of play. When I hit bumps I go flying. tell me what you think: This shows pitman to steering box nut: This shows the arm movement and angle:

I am installing a Rock Road high steer kit and the drop pitman arm (with tie rod end) is sitting on top of the tie rod :confused:. I need a stock pitman arm and cant find one anywhere! Any one around Tampa Bay have one????? Will pay, not looking for a handout!:2thumbsup:

Hello list. I am a new member currently installing an OME 2 inch suspension kit on my 98 TJ. This Jeep had a Rough country 4 inch kit with a rear track bar bracket already installed and a front adjustable track bar. I'm almost finished with the swap (reading forum posts has been a lot of help)...

I have recently sold my CJ. I have a NEW heavy duty steering shaft and dropped Pitman Arm for power steering box banging around my garage. I will sell both together for $100obo plus shipping. PM me and we will set it up.

Been doing a lot of searching & reading here and elsewhere on lifts for my '06 TJ. Interested in a 2.5" RC coil lift or 3.25" RC coil/spacer lift or 3" Zone coil lift. Both seem like they'd provide a good street ride (I'll say 90% of the time, but in reality, more like 95%) with some decent off...

I have installed a 4 to 4.5" lift on my cherokee. I have an adjustable track and a set of quick disconnects for my sway bar. I have also lined my steering wheel back up by turning the steering linkage. My problem now is that when the wheels are turned to the right, my steering linkage (where the...

I have lifted my cherokee around 4in and it threw my axle off center about 2in. Will this be fine or should I invest in an adjustable track bar? Also, will I need to get a drop pitman arm? Thanks for the help in advance.

I have rebuilt the steering gear box on my 58 Willys wagon and for some reason the pitman arm is not seating on the new shaft. I have lined the teeth up properly and felt it slip on, but it binds and won't budge with almost an inch left to go before contacting the frame, even when I try...

While changing my Steering box, I had those kind of mean pitman arm. I broke two of those 'regular' pitman arm puller, without any result. On both, the steel screw rip off the aluminum before the arm moved. Tried heet, BFH... no result Then I found a real puller ;) And the job was done in few...

What is this called? Its between the Drag link and the Pitman arm. How would I go to replacing this and where would I be able to get it. Thanks.

Is there an easy way to tell if my pitman arm is stock or a drop? The prior owner installed a 4" RC lift. I don't know if the pitman arm was changed or not. I don't know how flat the stock one is. I just installed the Currie steering setup last weekend and noticed that it said not to use a...

Can not get this thing to budge. Sprayed it down, let it sit. Broke two snap on pitman arm pullers and an OTC pitman arm puller. Best i can tell it hasn't moved. Any advice? :confused:

ok, i had a 4in rc long arm, 1in MML, 1.25BL put on 2 weeks ago now, i was up at rausch creek,pa this past weekend and begun to get play in my steering wheel, replaced the tire rod end that connects to pitman arm, but i still have play in the wheel, i also noticed that i can kinda rock the...