Search Results for ‘mounting’

So just the other day I decided to throw on a light bar that my buddy didn't want anymore and had given to me. Along the way, I did videos of how to wire it as well as how I built my mounting bracket for it to fit on my ZJ. I'm not sure if I'm allowed to put links in here, so I'm not going to...

Quick Fist Clamps FUELED 4WD is a Manufacturer Direct Supplier of Quick Fist Clamps By End Of The Road, Inc. End of the Road, Inc. has been making clamps for mounting tools and equipment on vehicles since 2003. We started with one size to hold shovels, axes and "D" cell flashlights, and since...

just ordered an mv50 compressor for my tj. i am planning on mounting it under my hood. wanted to do something like this (4x4Wire - Portable Onboard Air Installation) i have a/c and ABS. so i dont have much room other than relocating the evap canister, if that would even work. (NakedJeep ->...

Im looking into installing a CB system in my kj. I really dont want to have to drill any holes into my body because well.... I dont want to screw it up and be hating myself for it later on. First I was debating mounting a bracket onto my spare tire carrier but then I was thinking mounting the...

So Ive been trying to think of ways to mount a High Lift to a warn rear bumper with tire carrier. I searched and didnt really come up with anything, but I figure some one on here must have done this before. So if you have done this before can you please describe and or post pictures of what you...

Anyone have any ideas where to mount my jack and how I could do it?

2000 Wrangler TJ..I would like to see where everyone else is mounting there CB. We are new to the forum and the whole wheelin thing. we do have a CB in the jeep but the guy mounted it to the left of the glove box door and when you let the passenge seat up it hits.?? not good. any help would be...

Hey guys, Got my Rusty's 2 inch coil lift and steering stablizer wrapped up on friday. Looks good and waiting on new rims and rubber... I am having a clearance issue with the new stabilzer. It stated to use the OEM hardware but there is hardly room for the steering stablizer shock when the...

Edit: I just realized this should probably go into the General discussion thread. I'm totally on auto pilot because I always post in the TJ forum. :shhh: I've been doing some research on setting up an onboard air system with a York compressor. I've looked through everything on Kilby's website...

Hello, I am pretty new to the car modification scene, and had a question that might be really stupid, but then again I don't know much about car audio. I own a 2008 WK and noticed that in the trunk on the ceiling there is a fairly deep groove from about halfway back in the trunk to above the...

I've just purchased a NEW set of Wrangler MT/R W/Kelvar 31x10.50 but were mounted white letters in. The dealer states this is ok as they are not directional tires. But the tires say "this side inboard" on the outside. Should I be concerned?

The tire changer is great for un-mounting tires but the mounting process is a "hoe" I followed the instructions, as best as anyone can follow considering they were probably translated to English by an ambitious factory worker using Babel Fish, but ended up using a combination of ratcheting...

First off, if this is in the wrong forum, please move it to the correct forum. This is what I came up with as a mounting bracket for attaching the tow bar brackets to the front of my TJ. It is built from 3"x3"x1/4" angle. The same material was used to box in 4 different sections that I will...

Where is a good location to mount a Vair air compressor under the hood? I had it mounted on a tray under the master brake cylinder on my TJ but there is no tray there on the JK. Not sure if I like where the ARB air compressor bracket puts it and how a Vair air compressor would mount to the ARB...

Today I started taking stuff apart on my Jeep because tomorrow I will begin the process of repainting it. In the process of taking my rear bumper off, my dad and I noticed that the stock plat he had mounted the custom bumper he made was severely cracked. Here are some pictures: I have...

has anybody gotten the rola roofrack from 4xguard, and then mounted off road lights on it? if so, how? and what lights and wiring did you use?

when my dad bought his tj, the PO had a snorkel with it. the snorkel is brand new and has never been used. i know that the tj has a passenger side air box, whereas the zj has a driver side one. has anyone tried mounting a snorkel on the passenger side? i would actually prefer mounting it...

i was wondering if there was anyplace that i could mount some i.e (KC) off road lights on my stock bumper. if there happens to be any place i could anchor it to, would i need brackets or a mounting kit? i am very new to jeeps, but not clueless. :2thumbsup: thanks.

Hi guys, I need to get a CB Radio to head out on the trail with a Jeepers club I just joined. Thing is, I really have no relevance as to what is what and have never owned a CB before. I was hoping that I could get some recommendations on a good reliable CB and also some suggestions on where...