Jeep Enthusiast Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-12 of 12 Results
  1. Jeep CJ Forum
    I have a 1984 CJ7. The engine (inline 6, 100,000 + or -) runs fine around town. Can not hold 55 mph or get up a hill over 45 mph. I replaced the old Weber Carb with a new Weber Carb and fuel pump. I did the nutter bypass. Still the same issue, it runs well at light pressure on the...
  2. Jeep CJ Forum
    I have a 76 CJ5 with 54K miles. I got it 5 years ago with 49K and had the dealership here swap out the 232 with a 258 crate engine. I’ve had to repair little things here and there since then. 2 weeks ago I noticed that the ignition module had seen better days and decided to swap it out with a...
  3. YJ Wrangler Technical Forum
    90 YJ 4.2 bypassed computer installed MSD distributor years ago, Then last year she needed a new alternator and yep I probably picked the one with most amp out. So the charge is going to the ignition module and apparently that is what is burning ignition module since i have replace it over 6...
  4. Audio, CB/GMRS/Ham Radios, GPS, & Electrical
    I have a 2006 Jeep Grand Cherokee 4.7L V8. Last week it wouldn't start up, but rather just 'clicked' once and then nothing. The battery appeared to be good, but we went ahead and attached jumper cables to it, and it started up on the second try. The jeep proceeded to start up and run fine for...
  5. XJ Cherokee Technical Forum
    Hello Gents, New to the forum because I have a problem I can't figure out...how original of me! 88 xj automatic 6-cyl 4.0 So just the other day my jeep started having a problem. It can first be summed up by this video. That is me going from 0-25. It is like it can't decide what gear it...
  6. XJ Cherokee Technical Forum
    Anyone ever install an aftermarket ignition system? An MSD ignition module and coil to be more specific. Kind of curious where you mounted everything and I'm unsure of where to connect my 12V switch source. If you have any experience with them post it up. Thanks, Gnome
  7. YJ Wrangler Technical Forum
    I've been skimming through lots of forums and it seems i have a bad ignition module. I wanted to post my symptoms before i go pick one up and see if the wise people here on jeepforum agree with me. I will randomly have a rough time starting the jeep, which isnt the worst part. Very randomly...
  8. Jeep CJ Forum
    the ignition control module on my '76 cj5 (232 engine) is bad, and replacement ones will not work properly. I read in another post that the best option is to replace with a GM HEI system. My knowledge of ignition systems is limited... would someone please be kind enough to let me know the "for...
  9. Jeep CJ Forum
    last week i went out to start my jeep (1980 cj7 straight 6) and it would not start. it would just crank and crank and crank, but not turn over. after some investigating, i realized the ignition control module was toast. the stuff on the back had melted, and oozed down the side of the wheelwell...
  10. Jeep CJ Forum
    Hi again everyone. I decided to ditch my DUI dizzy and go back to stock due to smog restrictions here in Cali and my inability to get the DUI running the way I wanted (another thread). The Jeep was running sorta fine before I started this, so I know compression is not an issue. Specs: 1982...
  11. Jeep CJ Forum
    I have an 86 CJ7 with a 4.2L engine. Went to start it a few days ago and it fired and died immediately it did it 2 more times and now no fire at all. I figured ti was the ign control module so i had it tested and it checks okay. I replaced the ign coil pick up, the coil, cap, and rotor. Still...
  12. Jeep CJ Forum
    I am new to the forum and have a 86 cj7 with i-6 258. The jeep has been sitting for over a year while I found some money to get it painted and running. I have most of it done but I am stuck at my ignition problem. When I turn the key the gauges come on but when I turn it to start NOTHING. I...
1-12 of 12 Results
Top