Jeep Enthusiast Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 66 Results
  1. YJ Wrangler Technical Forum
    First off, hello. I've used this forum for a couple of years but made an account just now. I have an 89 YJ that I swapped an M57 diesel engine into. I've had an issue with my AX15 grinding in higher gears and have had no luck figuring this out. A little background on the build. M57 is a...
  2. YJ Wrangler Technical Forum
    Hey fellas, any help would be much appreciated! My ride: -94 YJ 4.0 SE -33in tires, and ~3in lift (lifted when I bought it and I don't know the exact lift) -AX-15 (I think) 5-speed manual transmission -I do not drive it hard, and off-roading is limited to whatever is necessary to get to certain...
  3. Engines & Drivetrain
    Car started making a grinding noise at the front of engine on passengers side that gets louder when it is idling. Sound like two gears are not meshing properly. It is not the transmission.
  4. ZJ Grand Cherokee Forum
    I've got a killer little '98 ZJ that I've been fixing up to be a comfortable daily driver. I'm trying to fix every detail I can to get it there. One of the current issues is the power lock actuators. When I push the power lock button on either door panel, all 4 actuators make a "GRRRR" sound for...
  5. Jeep CJ Forum
    VIDEO OF THE NOISE: Hey guys, I have 1977 Jeep CJ7 with a DANA 300 t-case and a T150 tranny. Just finished swapping in a 304 and took it out for a test drive and heard a grinding noise coming from what i thought was the tranny, so I changed the fluid and the noise went away in 2wd only, so I...
  6. YJ Wrangler Technical Forum
    Alright so, busted what i believe is my locker. Every time i put it into 4x4 and drive any faster than 30 whether it be ice or snow, theres an intense grinding sound and all of a sudden my steering will jerk to the right. Im assuming its my locker and have already bought one. Thoughts? Happen to...
  7. WK Grand Cherokee & XK Commander Forum
    Hey everyone, I have a 06 GC and am having a bit of a problem. I have a "grabbing" happening in the front driver side wheel only when I first crank up and begin to roll away. When I power through it it gives way and wont happen again until I turn of the car and crank it back up. My service 4wd...
  8. Engines & Drivetrain
    Hi Jeepforum. I have a 1995 Jeep YJ SOA, 33's, 5spd with 8.8 rear, NP231 w/ SYE. Recently when I have been doing light rock crawling I have been experiencing intermittent "Grinding" or "Scraping" metal noise whenever I hit a steep incline. The noise has only ever occurred when I am in 4Low...
  9. YJ Wrangler Technical Forum
    This week seems to be the week of Jeep problems for me... My project YJ has developed a fun issue. Since I picked it up a month ago or so, it has seemed to have issues going into second gear. The moment you let off the gas, it pops right out. That was the first thing. I recently put a 1.25" body...
  10. TJ Wrangler Technical Forum
    Got a 98 with the 32RH 3 speed auto tranny, and it's beginning to act up. When the jeep is cold, if I throw it into reverse, there is a clearly audible grinding/rattling/buzzing. Sounds a bit like stones being vibrated inside a tin can. The noise will eventually fade away after about a minute or...
  11. YJ Wrangler Technical Forum
    Hey guys, i have a 1993 Yj, 4L automatic. Recently the rear driveshaft was broken so it has been parked for a bit on my driveway. Today I need to move it so I could get my other car into the garage. Went to start it and it did, idled smooth. Then I put it in 4High and went into drive. it...
  12. XJ Cherokee Technical Forum
    Alright guys went offroading yesterday,used 4 hi, when I was done I went back to 2wd. Noticed some whirling sounds when I got back on the road. This morning trying to figure out whats wrong I check the rear diff and its fine. But I turned over the xj and went into 4 high no problem. Put the...
  13. TJ Wrangler Technical Forum
    So after the worthless Dana 35 kicked the bucket for the second time, I decided to swap it out with a custom Ford 8.8 from East Coast Gear Supply. They recommended adding a SYE to replace my T-Case drop at the same time so that they could properly set the pinion angle. I took the project to my...
  14. YJ Wrangler Technical Forum
    I just bought a 1990 Wrangler with a 4.2L and a 3spd auto I have got the engine running a lot better due to everyone's helpful knowledge here so here is the issue my jeep had started making a loud pop here and there that felt like it was right under me I thought maybe a ujoint was going bad...
  15. YJ Wrangler Technical Forum
    I just finished replacing the clutch, slave cylinder/thowout bearing, master cylinder and pilot bearing on my 92 YJ with the 2.5L and AX5 transmission. I also replaced the 5th gear snap ring and installed a snap ring retainer. Now that the whole thing is back together, there is a constant...
  16. TJ Wrangler Technical Forum
    Hello all, I have a 2004 wrangler x 4.0 5 speed. While taking off last night just after I released the clutch in first gear the transmission started making the loudest grinding noise, I cant move forward at all it just grinds (sounds loud and alwful ) and it doesn't want to move forward at all...
  17. XJ Cherokee Technical Forum
    Anyone have this before, or have any idea what it could be? before i list the details, here are the parts I've already thrown money at and they are no older than a month old Ball joints on knuckle (driver side) U-joints to wheel (both sides) new brake rotors and pads (both sides) new wheel...
  18. XJ Cherokee Technical Forum
    2000 XJ 4.0 AW4 stock height Hey all, long time lurker, very infrequent poster. This is the first problem ive had that I cant seem to wholly solve :thumbdown: Okay so a few weeks ago my stock starter seemed to be starting with less umph so i pulled it apart, cleaned it out and popped it back...
  19. ZJ Grand Cherokee Forum
    im sure this has been covered before but I figured id still share this with everyone :thumbsup: so my rear brakes were somewhat catching/grinding so I popped the wheels off and pulled the brake caliper off and found worn in notches in my caliper brackets. so for this repair you need a welder and...
  20. TJ Wrangler Technical Forum
    Just bought a TJ yesterday. Having problem right out of the gate... I was hearing a faint metallic grinding/scraping noise when in higher gear while driving. (It's an Automatic.) I jacked it up today and spun the wheels in 2H, 4H, N and 4L. In all but neutral, i could hear a very distinct...
1-20 of 66 Results
Top