Search Results for ‘egr’

Hello, I have a 1981 CJ7 that I have been restoring for the last 6 years and I recently took her out of storage. Oil is new, coolant is topped off, and fuel is full. I have a Weber 38/38 DGAS and a HEI distributor on now (all vacuum lines are brand new). Yesterday as I was driving it, every time...

Hello. I've been having multiple ongoing problems with my ZJ for a while now. The problem codes remaining are 53 (internal self test malfunction) and 32 (EGR solenoid circuit). My symptoms are as follows: -Intermittent stalling after coming to a stop or going a very slow parking lot speed. Pops...

Me needs help, on my 08 JK I had a code P1404 EGR close position, P0205 Fuel Injector, P0404 EGR “A” Control circuit range. I replaced the fuel injector using OEM from the dealer and ordered plugs,wires,EGR, and ignition coil from rock auto. After installing the fuel injector I was good no...

Hi, I have a 3l diesel overland which just clicked over 100,000km and my inlet swirl valves have seized up. I’m thinking of doing the banks inlet manifold replacement and binning the EGR system. Has anyone done this and if so I’d be super grateful for advice and tips! cheers

Hey, I have a 2008 jeep grand Cherokee 3.0L diesel, and I am having EGR issues. I took the EGR out and cleaned it, hoping the code would go away, but I am still having problems. The codes are P0403 and P0404. I took the jeep to a local shop and they said I need a new EGR. A new egr on the...

I just finished driving about 10,000 miles over 8 months. I have a 2009 Jeep Ultimate X 4 door. Nothing special about it, stock, everything. The 10,000 miles were all highway and doing about 65mph. To ensure that I had good gas, I purchased high test as soon as I started out on the trip. Within...

I had been getting an EGR trouble code (I forget exactly which one it was) on and off periodically. So I replaced my EGR valve and the code went away for a few weeks. Now the light has come on again and I'm getting P0401 - something about insufficient EGR flow. I don't know if the new EGR...

The EGR port in my exhaust manifold is blocked off with a small plate and always seems to leak so i made a gasket out of a gasket for a different year because there apparently isnt one for this year. Anyway, it seems to be leaking from the top and bottom again where there are no bolts holding it...

About a month ago I got a check engine light for an EGR valve(P0404) and then I replaced it, and it got better. The light went off, acceleration was smoother and gas mileage was better. Today it came back on. Any ideas? Maybe the new valve went wrong?

Hey All - Replacing my EGR tomorrow, and want to just buy a replacement bolt ahead of time to avoid any potential drama with cutting the original bolt once everything is apart. (Murphy's Law says I'll cut it too short and will be stranded unable to drive to the hardware store for lack of a...

So I have a silly question. I have a 95 zj limited 5.2, I've straightpiped it. I was reading through my service manual on emissions and came upon a concern with the egr system. To my understanding, the EGR control solenoid is controlled by the PCM, which opens or closes the valve depending upon...

I'm changing the valve cover on my 1992 XJ w/ 4.0 liter and have a semi-retarded question.... For the ports for the PCV and EGR (one line back to air filter, one back to intake manifold), there are 3 small bolts securing a triangular shaped aluminum piece to the valve cover (one for each port)...

This guy needs help... Bought this 2007 CRD from a guy about a month ago. First thing it did when I got it home was not start. I figured out it was the crank shaft position sensor, so I put a new one of those in and a new crank case position sensor. Started ran good. Friday I'm pulling around...

Ok I'm totally lost here and this is my SOS/distress call. My 81 CJ7 258 somehow has a Carter BBD without the stepper motor, no computer, etc. My problem is, I'm trying to hook up the vacuum lines as proper as I can, but when i try to follow the diagrams I found online im missing some of the...

Hey guys, I know there are some other threads on this stuff, but I didn't want to hijack them with my own issues. The pictures below are of my 89 GWagoneer with a newly installed Edelbrock Performer 2131 Manifold and 1406 Carb. We were able to get them installed just fine, but we are having a...

I recently started to work on and fix my Jeep to get it running right. Cap,Rotor,Wires, Plugs,Mech Fuel pump, Exhaust next thurs. While checking the PCV valve and vac hoses I found a brooken component on my carb. It faces the engine and has a plate that used to be held on with push pins. There...

Please take a look at my questions and symptoms I would love ANY ADVICE.I am just beside myself right now, ever since I did the nutter and installed my brand new weber 32/36 I've been having nothing but trouble trying to get my YJ to run right. The engine only has 30k miles on it and I really...

Guys/Gals, I am a novice and need some help. Here's my story. I have a beautiful 83 CJ7. I am putting a 304 in it. I bought a 304 and am going to send it to the remanufacture shop. I am going to have them put the engine together for me. What I mean is I am asking them to put the intake manifold...

hello! hope someone can help me since i am pretty lost here. i tried to find a similar threat in this forum, but so far i have not found anything that really matched. sorry though in case i have overlooked a threat. i installed the new carb the other day. i did not end up using the old air...

I just purchased my first Wrangler, it's always been on my bucket list to grab one and I finally did a couple weeks ago. The first couple weeks I had it the engine sounded fine... great actually. This past week I noticed that it had developed a ticking noise over only a span of only a couple...