Search Results for ‘drive shaft’

As the title says, I am at a loss for finding the correct sized U joint for my '09 grand Cherokee. I found ONE auto parts store that carries them, but they are factory direct, and it shows 2 different parts. I am able to order the 1310 or the 1330 but cannot find info online anywhere for which...

242HD transfer case, front and rear drive shafts, shifter bezel and new seals. Removed from an 03 WJ with the 4.7L. Located in Frackville, PA but willing to meet up to 4 hours one way. Asking $400 OBO.

I can slightly twist/wiggle the rear drive shaft. Here is the video recording Is this normal? I can feel vibration/resonance from underneath when accelerating within a certain speed range.

Hi, I have no knowledge of lifted systems, so answers in layman terms would be appreciated! Recently I bought a used lifted YJ (95 straight 6), and replacing the rear drive shaft was recommended by a trusted mechanic. After he took a look at the rear drive shaft that's currently on the Jeep...

Today as I began to pull away from a stop light there was a lot of grinding and suddenly my Jeep would not move. I tried switching between D, 1, 2 and none of them would get it going again. I finally tried putting it into 4Hi and I could drive and get going again. Once I got to work I tried...

I'm undercoating the Dub-J with POR15 either this weekend or next weekend. While I'm under there prepping, I wanted to clean up the drive shafts. (they rusty as hell looking....lol) Thinking wire-wheel them, and then either rattle-can paint them or use the POR15 on them. POR being a lot...

Looking to buy a 03 TJ Sahara 4.0L 5 speed. Asking $6000 Cons: 266K miles Broken Windshield Pros: Drives well (good power, clutch feels strong, shifts smooth, no shimmy or shake) Body appears excellent New tires New clutch Everything works (radio, ac, gauges). Major Issue: The drive shaft...

I'm about to replace the driveshaft of a '06 WK since one of the u-joints has play and is producing vibration at highway speeds. The replacement will be a new all steel driveshaft. I was looking at the service manual and it lists the torque spec for the bolts at either end (trans, diff) at...

I am needing to replace my front drive/propeller shaft in my 05 Jeep Grand Cherokee with the 4.7L V8. I'm not too sure on the length of the shaft however, I am having issues finding the right one. My drive shaft has U-Joints in the front connecting it to the front diff and a CV-Joint at the...

I blew out the cv joint on the differential end of my front drive shaft (1995 ZJ 5.2L, stock drivelines, D30, 249 t-case). It was the middle of the night ~ 7 miles from pavement on a somewhat icy/ snowy hill. Rear wheel drive with open diffs in those conditions is useless, so I slept in the back...

For the most part, when you install a Metalcloak Lift Kit on your JK, replacing Drive-Shafts is not a "Must-Do", which saves time and money. Over time, though, stock drive-shafts will wear out and need to be replaced. So, whether you want to do it all at once or wait a year or so, Metalcloak...

I've had a thought for a while about why I couldnt get my front driveshaft into my 92 yj mainly because there were just holes and were deep enough a u bolt couldnt get through there. I bought a np231 from a guy, however I now realize the front yoke is for a double cardan style joint. I dont have...

will my stock front drive shaft still be fine once I put the 4in lift on my 98 tj or will I have to get a custom one

I have been searching and searching for the proper service procedure on how to re-do the Pinion seal in the front differential on this vehicle. It is a 97 Jeep Grand Cherokee Laredo with all stock drive shafts and axles. I am willing to pay the $150 I have been quoted if you guys really think I...

Well it's time for my first post. So I recently purchase a 1993 Jeep grand Cherokee Limited 5.2L for a really really good price. The reason I got it so cheap is because it makes a clicking sound while I drive. I've done a little research on these forums and after a while I came to the conclusion...

I have a 1979 CJ5. Stock transfer case and stock rear end. I have it lifted 2", as well as running 33x12.5 tires. As recent as 2-3 weeks ago, I have noticed that I am getting drive shaft slap when accelerating/decelerating. I am thinking that somehow the angle is off. What angle should I be...

So apparently my cv joint is bad on the front drive shaft. I have a 2004 Liberty Limited 3.7 with 4wd. I see that many people do change just the cv joint instead of the whole drive shaft. My question is how do you know whether to change only the joint or when it is best to change the whole drive...

I recently bought a '05 LJ (6 speed). It has a 4" suspension lift and (apparently) a new aftermarket driveshaft. There's an weird "whining" sound when I apply gas at lower gears and I want to rule out the rear differential so I went to disconnect the drive shaft. Unfortunately, since I've never...

It finally happened - my Rezeppa/Fixed Yoke front drive shaft bit the dust. Considering it had 135,000 miles on it, 35,000 and 3 years of which on a ~3" lift, I'd say it did pretty good. Let's start this post with an illustration of all the drive shaft options for our WJs: In a perfect...

Hi guys, new to the forum and have a driveshaft question. I am in the process of finishing up the drive line on my new project, a CJ5. I have a 6" suspension lift asking with an axle over conversion. I swapped out the stock axles for a 44 front and an offset 60 that came off of a J4000. So the...