Jeep Enthusiast Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 291 Results
  1. YJ Wrangler Technical Forum
    1994 YJ 4.0L with AX15 (external slave) Howdy. I just replaced my clutch disc, pressure plate, throw-out bearing, pilot bearing, clutch fork pivot, and the little pivot spring. This is my first time replacing a clutch. I checked the master cylinder reservoir and the fluid was quite low, so I...
  2. XJ Cherokee Technical Forum
    Recently purchased a 2000 XJ with 143,000 miles and its pretty clean seems to have been well taken care of but theres one thing bothering me with it. I am having problems with crunchy feeling/rough shifting mainly into third gear. It doesn't happen all of the time but more often than not It...
  3. JK Wrangler Technical Forum
    So my JK has been problematic recently. First it started with 2 month long (and three dealerships) overheat issue which after new radiator and hoses, and multiple new water pumps and thermostats was determined to be the dreaded left cylinder head, my clutch started to stink. Figuring with just...
  4. Jeep CJ Forum
    hi there! 1986 CJ7 Laredo. Just hit 100k miles the other day, and as a thank you gift, my clutch stopped working. I was on a hill, in 1st, when I felt a pop on the clutch. Since then, I can’t get the car into any gears. Clutch pedal has no resistance for first half press, then second half press...
  5. YJ Wrangler Technical Forum
    Hello Jeepsters, It's time to replace my clutch ( she's lived through a few clutch Mcgyverings already,127k). I won't be doing this myself, but since I must use a mechanic for this repair, becasue really Jeep, ya gotta take out the whole tranny to fix the clutch??@!%$. This is the only thing I...
  6. YJ Wrangler Technical Forum
    Hey everyone, I recently swaped my transmission and realized I was missing two bolts and can't find these bolts anywhere, they don't hinder the performance of the car but there's a rattle when it's not on, I have a 1994 jeep wrangler yj 2.5L with an ax5 transmission. If anyone knows the thread...
  7. XJ Cherokee Technical Forum
    I've got a 1990 XJ with a 4.0 engine and the Peugeot BA 10 manual transmission. I replaced the flywheel, clutch, and slave cylinder but now it doesn't want to shift when the engine is running. It shifts through all gears fine with engine off. I’ve thoroughly bled the clutch, multiple times...
  8. Jeep Wrangler Forums
    Hi there, I'm new to the forum (thanks!) and have a 2011 Wrangler 4 door, 6 sp, hardtop, that needs a bunch of work, more than I want to take on. Needs a clutch, sensors, and tune up. Just got new U-joint, is in great shape (bodywise). Sadly, I need to move on. I love it but I don't fix cars and...
  9. Jeep CJ Forum
    I was pulling out of my driveway for PT last Friday and as I was depressing the clutch on my '84 CJ7 it made a popping sound and then it sputtered and died. I started it back up and the clutch still had resistance but I could not get it into gear. I wasn't able to get underneath it before my...
  10. Jeep CJ Forum
    I'll be dropping my new to me 86 CJ7 off at the local 4x4 shop Saturday morning to have the engine tuned up and the carb gone through. Gonna have the clutch, suspension and brakes inspected. Ive researched the VIN, and it shows the jeep came from the factory with the 258 I6 and an auto...
  11. YJ Wrangler Technical Forum
    Hello everyone thanks in advance for any help with this. The problem is when I get onto a freeway on ramp into higher speeds/rpms I accelerate quickly to match traffic speed and as im shifting through the gears I end up having to reach pressing the clutch pedal down further to feel for when the...
  12. YJ Wrangler Technical Forum
    Hey everyone, I am upgrading my transmission in the 88 yj from the garbage BA-10 to either an AX-15 or the NV3550. Will my current clutch system be compatible or will I need to replace that also? If replacement is needed, recommendations for a new clutch?
  13. XJ Cherokee Technical Forum
    I have a 1991 xj with an AX15 swapped into it. The clutch went bad and I can’t seem to find a new clutch for it. It has an internal slave cylinder. Can anyone share where to find a clutch?
  14. YJ Wrangler Technical Forum
    I've searched around and from what I've seen so far I'm looking at an input shaft bearing as the culprit. The posts I've read don't quite match the symptoms I have so I just want to make sure I'm heading in the right direction. The vehicle is a 1990 Wrangler with the 2.4L, 5 Speed manual...
  15. XJ Cherokee Technical Forum
    Hey there, owner of a Manual 4.0 I6 1992 Sport. Recently the clutch pedal went out and the car doesn't go into gear while running. I assume there's a leak in the clutch master cylinder, Does anyone else have any viewpoints on the issue? Also, who knows how to bleed the clutch on a manual XJ? I...
  16. XJ Cherokee Technical Forum
    I have recently been having trouble with my clutch, and I am going to do a bleed of the fluid, and I saw that the quick disconnect connector to the slave cylinder is missing an o ring. Does anyone know the order of o rings and washers that go inside of the quick disconnect connector? Thanks
  17. TJ Wrangler Technical Forum
    Planning some work on the 2004 TJ, and recently ordered a Centerforce Clutch Throwout Bearing from Quadratec, and just realized that it is listed to fit Wrangler from 94-03, P/N N1764. Centerforce's website has the N1764 listed to fit a range of models and engines, but under separate listings...
  18. General Jeep & Off-Road Equipment
    I have tried to search online for a list of things to check but all I can find is "did you check the Clutch Safety Switch??????" Yes, that was the first thing I did. It creates a circuit when depressed fully. I also get power to the plug that the switch plugs into. When I do need to move it I...
  19. Jeep CJ Forum
    t150 shifts gears when not running but no dice when running. Starting simple with filling and checking transmission fluid but this fill plug seems impossible unless there is some kind of square of hex indentation on the top. Anyone have any idea what would go in the top of it so I could...
  20. Engines & Drivetrain
    I have a 1990 YJ with the 4.2L engine and 5 speed transmission. I have replaced the clutch assembly with a new flywheel, pressure plate,slave cylinder and master cylinder. The problem I am having is the clutch will not disengage after I drive for about 5 minutes. I have replace the new master...
1-20 of 291 Results
Top