Search Results for ‘bracket’

I'm hoping you guys can help me figure out my part mystery. I've got a 2006 3.7 with the 3.73 front diff. I went off roading with some friends and cracked the passenger side axle housing that mounts in the diff. That axle housing has a flange on the end and theres a bracket that runs...

Rancho® Front Track Bar Support Bracket for the Jeep Wrangler JL and Gladiator JT is designed to reinforce the front frame side track bar bracket. Made from high strength low alloy steel, this new support bracket reduces the threat of a failed OE bracket when lifted or running larger than stock...

As part of my restoration I realized that I needed new leaf springs. Bought the new springs. and installed one. Discovered that the new springs are shorter than the ones that were on it. I have no idea if the ones I removed were original, or even correct. I verified that the new ones are the...

We have recently updated our control arms to be rebuildable and you can now purchase as a set or by axle. Our D2 bushings are now rebuildable too!! These arms are beefy with 2" OD on the lowers and 1.25" OD on the uppers! Reduce road noise, vibration and get improved handling. Check with your...

We have recently updated our control arms to be rebuildable and you can now purchase as a set or by axle. Our D2 bushings are now rebuildable too!! These arms are beefy with 2" OD on the lowers and 1.25" OD on the uppers! Reduce road noise, vibration and get improved handling. Check with your...

We have just launched our new ADJUSTABLE front and rear track bars, center your axle easily with these adjustable track bars using our D2 rebuidable bushings. Our D2 bushings do an amazing job of absorbing road vibrations. Made with 1.25" OD diameter DOM for handling what is thrown at it. Check...

Hello everyone, I'm pretty excited to have just bought my first Jeep. But It's time to button down and get to work. I have a bit of work to do to get this beast road worthy. Top of the list is the axle issues. The Jeep was previously in an accident and was struck on the back right wheel...

Hey guys, I've got a busted steering stabilizer mount. Broken in more than one place and it looks like its been welded at least twice before. Does it look like it can be welded again? Should we even bother? Or would I need a whole new axel? Any suggestions? Thank you for your time:):) BTW, when...

Hey there howareya? Wanted to share with ya my mod of the TJ OEM license plate bracket. I wanted a plate that hugged the jeep and its curves :shhh: but I didn't want to buy an expensive bracket or drill any new holes in my TJ. I started looking at the OEM bracket and realized all I needed was...

Replacements for these cost over a hundred dollars. Mine was in 5 pieces, but I used Locktite Plastic Bonder Epoxy (syringe with two parts that you mix together) on it and it worked amazingly well. The epoxy bonds the plastic and gets really hard, maybe even better than the original if you...

My '90 YJ came without a radio. No problem, I purchased a factory AM/FM to maintain a factory look. It appears that I'm missing a bracket because the radio is about 1" smaller all around than the dash opening. Secondly, does the radio mount behind the bezel (flush with the heater controls)...

I thought I would do a more recent JunkYard seat replacement write-up: After wheeling a couple weeks ago, my drivers seat really seemed loose, and even rocked when I would shift - so I reviewed this forum thread - jotted some notes on my cell phone, about what models to look for the next time I...

Hello all. In the midst of my 4.0 swap, and the donor motor didn't come with all alternator mounts. This is a '94 4.0 out of a '94 going into my '95 Wrangler. I have a new Grand Cherokee alternator, and I have the upper AC/alternator mount already installed. I do not have the lower bracket...

I want to mount 100w KC Daylighters on my 2010 JKU Sahara, will they fit with these? http://www.quadratec.com/products/12110_201.htm What about the quality of the product alone? Does anyone know how easy they are to install or how well they hold up?

Hey guys...... I've searched the internetz extensively and have not found a clear-cut solution to my problem. I was driving the other day and noticed the @ss end of my Jeep getting squirrely. Got out to check the suspension and this is what I found: Here she is: It's a 2004 Rubicon with...

Hey all, when I first bought my jeep I was told the hydraulic lift arm for the rear window needed to be replaced. The passenger side arm was already removed, so all I needed to do was get a new arm and install it...I attached the new arm to the glass with no problem, then at the bottom of the...

i was in the process of a weekend rebuild/seal. put everything back together and i cannot for the life of me figure out how to arrange my brackets to support my alternator . im always left with a extra ^6" bolt with a slight 'Z' bend to it. plus. so i know the bolt goes in some where close, and...

I'm installing a Rough Country 4" X series lift and it came with a rear trac bar relocation bracket. I just can't seem to get the trac bar lined up with the holes in the bracket. Any tips or advice would be greatly appreciated. I'm pulling my hair out here.:confused: Thanks

Does anyone know where I can find the bracket that the rear tire carrier bolts to (on the inside of the tub) and the tail gate cable bolts to on the body for a cj8 scrambler? The jeep was missing them when I bought it.

OK long story short...how do i get this bracket back inside of the windshield where it belongs?? so i can then proceed to hook up my KC's Or am i screwed and have to do something crazy..? also as you can see the torx screws are a pain in my behind..should i just replace them with regular bolts?