Search Results for ‘bolt’

Does anyone know the thread pitch and diameter for the mounting bolt that holds down the fuel pressure regulator? Mine snapped in half when installing a new regulator. Thanks.

Long story short-ish: Did an engine swap on my '90 XJ 4.0. PO said he cleaned up the head and put it on a used block. Upon initial startup of that mix-matched block and head I heard what I thought to be a loose/worn rocker or pivot. Turns out it was a stuck lifter. Ok, not THAT big a deal...

I'm in the JeffCo area, just south of STL. I have had alot of health problems (kidney's) which have kept me from getting a simple t-stat job done. A friend was supposed to do it for me since I'm in alot of pain most times but he hasn't done it yet and I can't keep putting it off. My heater core...

I've been having some problems with a vacuum leak on my '02 recently(I shoved a sock in the intake and it kept running). i did a gasket swap a few weeks ago when i was tightening up the bolts that connect to my exhaust. I assume it was just a poor gasket or the manifold bolts didn't torque right...

I got some Mopar rock rails for $80 on Craigslist, but they didn't come with mounting hardware. I have never mounted any before either, so I eyeballed it and thought I would be reusing the body bushing bolts. Turns out there are bolt holes already in place, and your new stuff should come with...

For those that have replaced the front lower clevis bolt (the infamous bolt), do you remember either the part number or the size? :confused: I've been searching and I think M16x2.00x135.00 is the correct size? Here...

I have a 2004 TJ with the NV3550 5-spd. Does anyone know where to buy replacement drain and fill plugs for this tranny? I am going to change my fluid soon. The drain plug has rust on it and I would like to buy a replacement before I remove it. I've search online and in the forums, and cannot...

I took the doors off of my '93 Wrangler YJ a few months ago, but in the process of taking the drivers' side door off, I destroyed one of the bolts. I've been looking online for a replacement, but I'm having a hard time finding what I'm looking for. Can anyone point me in the right direction?

Adding front bumpstops to the spring pads on my LJ. What size hole do I drill and what size bolt do I need? I heard I can drill a hole and get a self tapping bolt but I am not sure what size I need. For example, what size bolt fits a Rubicon express bumpstop.

Picked up a 2000 tj and it is missing the rear left front passenger seat bracket bolt. It is a different size then the rear right bolt. The chrysler parts dealer doesnt even know what size it is. Does anyone know the size of this bolt please?

Im in a bit of a pickle here: I changed the clutch about a month ago and removed the whole shift tower at the time by removing the 4 bolts (as compared to the other method). They were stripped so I went to the stealership and they wanted $17 for the 4 bolts :O So i decided to grind slots in the...

Ive got a 2000 TJ with 140k miles here in New England, I'm trying to remove the rear bump stop cups to repaint and add bump stop extensions for my spring install. Both of the bump stop bolts will back out about an inch and then they just spin and don't come out any further. I cannot see the top...

My steering is rather sloppy on my cherokee. Found the steering box, however im not sure what to tighten to help my steering. Is the bolt under the steering box?

I have a '98 GC. The front left sway bar link broke. The ball joint comes out of the socket. I got most of it off, but the ball and the threaded bolt connected to it are stuck in the end of the sway bar. Any suggestions on how to get it out? I got a Pitman arm puller, but it ended up being...

This week I finally got all my OME pieces togther and was installing this weekend. I have an 07 WK Limited Hemi QDII. So I started the project, with it being pretty straight forward..I still had my laptop in the garage with the OME instructions and the Full digital FSM...and off course a full...

The bolts that attach the hub are a 12pt size 13, this I know. But mine are stripped! I can get em off (thats a story in itself :brickwall)...but want to replace them. What size thread and length are they? I will get some at the hardware store...I do not want to pay $10 a piece for them from...

came out to my car after work today to find the gas tank almost on the ground. don't know why, but all four of the bolts attaching the front of my gas tank skid plate are missing. I ratchet-strapped it to get me home, but I really need to know what size they are, so I can find replacements...

I was trying to take my doors off my 2 door jeep TJ and the bolt snapped and now I'm left with the screw still in the hinge with the bottom of the bolt broken off.. :mad: What should i do? :confused::confused::confused:

I have a couple that are seized and don't want to come free. Figured I would replace them all and keep the ones that come off as spares. I called the dealer with the part numbers this morning and after hearing how much they wanted ($160 for four bolts washers and nuts) I said I'll get back to...

hey all first post. I saw another post similar to this topic but it seemed to be old so I made a new one lol. anyway I have no Idea where the bolt went when I took apart the thermostat (bottom one/ shorter one) no idea what so ever it may have went into a little cavity any how can I use any...