Jeep Enthusiast Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 21 Results
  1. WK Grand Cherokee & XK Commander Forum
    Hey y’all, I believe I’m having an issue. I have a 2010 Grand Cherokee. Was changing out the passenger side strut when the wheel hub assembly leaned forward causing the cv axle to unattached itself from the stub(intermediate) shaft. Didn’t notice any damage to the cv axle, but went ahead and...
  2. WK Grand Cherokee & XK Commander Forum
    Hi guys, looking for a Dana 44 expert here. I'm going to rip out IFS and replace with a Dana 44, get at least a 6" lift going and install 35s. I know the JK Dana 44 is not the same as a regular Dana 44, and cannot find an inexpensive option for JK Dana 44 and don't want to drop nearly $4k on a...
  3. Engines & Drivetrain
    Rebuilding my AMC 20 Narrow Track Rear Axle and I hear a lot of people talking about replacing the 2 piece axles with 1 piece axles... I'm curious about this upgrade because I've also heard of people having a lot of problems with the 1 piece axles falling out because the bearings fall apart...
  4. YJ Wrangler Technical Forum
    Hi everyone! I'm in search of some answers regarding rear axles in the YJ's. I have a 88 YJ Base that I bought a while back. When I bought it the previous owner said that the owner before him replaced the rear axle with a higher ratio gear setup. I'm not sure what it is currently but I know the...
  5. ZJ Grand Cherokee Forum
    I have a 97 laredo and began to hear & feel clicking sounds (moving in a straight line) in the front. 6 months ago, I had the front axles & hubs replaced and everything was working well up until a week ago (with the click sound). I jacked up the front and put on jack stands to spin the wheels...
  6. Engines & Drivetrain
    While installing new bearings onto new 1-piece axles, I failed to notice the inner race was no longer supported while pressing, resulting in bearing damage. I was grinding down the inner race, trying to thin out the back side just enough so I could finish splitting it with a chisel, when I...
  7. XJ Cherokee Technical Forum
    ok bad news i think looking at my front end. the whole assembly seems shifted to the driver side. my (looking at the truck from the front end) left upper control arm seems straight front to back, and my right side upper is at a angle outwards. along with the bump stop in the left side spring...
  8. Jeep CJ Forum
    I've searched three different forums and can't find an picture intensive rebuild or and answer about the ball joints on a 77 CJ so I'm coming here. I have the service manual as well as the Chilton's book and neither has been very specific about this process. However, I have been able to figure...
  9. Engines & Drivetrain
    Working on my first WJ project, and I have blown axle seals and pinion bearing in the rear. My question is can I take out the ring gear, and remove the rear drive line so I can still drive her? or will it mess up my transfer case since it is the quadra drive with vari-lock?
  10. YJ Wrangler Technical Forum
    I'm thinking about putting Locking or Limited slip in the front and rear of my 1995 Wrangler Sahara. anyone have preferences or suggestions for me? keep in mind that this is my daily driver also. Thanks guys! :wave:
  11. Jeep CJ Forum
    I am working on the rear axles in my brother's CJ-7 for him. The passenger-side wheel hub was slinging rear-end fluid badly so I figured the inner seal was blown. My current issue is the castle nut on the passenger-side is LOCKED on. After breaking two 3/4 to 1/2 inch reducers with a cheater bar...
  12. XJ Cherokee Technical Forum
    What just happened? - Need Advice Hello everyone, I am new to owning a Jeep Cherokee and still don't know a lot (EvoX 750+hp.. slight change of pace). If I could get some input on why this situation happened and how to make sure it does not again, it would be greatly appreciated. So here it...
  13. TJ Wrangler Technical Forum
    As the title states I am a "Newbie" to the Jeep. I inherited mine from my parent and am loving it, but I have recently ran into a problem. Recently I found out it needs a complete rear axle assembly. My mechanic has been looking for it at salvage yards and other places to try and find one around...
  14. TJ Wrangler Technical Forum
    the undercarriage of my 99 tj is looking pretty bad from all the salt on the road. and with the amount of wheeling i have been doing, the rust is kinda making me worried. all of the vin numbers and ID tags are rusted to the point of being unreadable.:( so dose anybody know the size of the...
  15. Jeep CJ Forum
    Anyone using any front axle seals on their dana 30's? I am goign to use the factory axles are they are still in good condition. However it appears that there was a flange or seal seat on the inner axle where it would seal against the axle tube. I cannot find any factory replacements. Is anyone...
  16. General Jeep & Off-Road Equipment
    Well, I actually just got the jeep, and the previous owner lifted it, and put on the 35's, and didn't touch the brakes, so $300 later, I had purchased new vented and slotted rotors, AGGRESSIVE pads, and some new wheel hubs (just because they are going out) anyways, after I tore everything down...
  17. Jeep CJ Forum
    Does anyone have a pic of how the driver side read axle seal by the break back plate goes? I put seal on axle housing and then put on the back plate and it just don't fit right. Any help here is greatly appreciated.
  18. XJ Cherokee Technical Forum
    Recently noticed my D35 leaking gear oil a lot.:thumbdown: So I'm hoping I just need to replace seals. So far it's only the passenger side right now. But before I buy stuff I was hoping to see what seals I should get first. Axle tube, inner axle shaft, or outer axle shaft. I was also gonna get a...
  19. Engines & Drivetrain
    Hey Guys, I got a leak on the front right hub area of my jeep. I want to replace the seal on that side. I have a 2001 Jeep Wrangler 4x4 sport 4.0L where and how do I know my gear rato and which Dana axles I have? Ty Dwight:highfive:
  20. TJ Wrangler Technical Forum
    I have been throwing around upgrade ideas for my Jeep and would like some feedback about cost, difficulty, idiocy, etc. for a newbie DIY. Right now I am running 33s on a 4" lift with stock gears. My goal is to get gearing to 4.56 with front and rear selectable lockers. I was comparing the...
1-20 of 21 Results
Top