Jeep Enthusiast Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 28 Results
  1. Engines & Drivetrain
    I’m in the process of building a 4.0 from the ground up. I started with 1987 4.0 and stroked it out to 4.6. It has a 1995 7120 ported head and larger LS valves. The CR is +12:1 and will run on propane. Ultimately the engine will be installed in an antique truck. There’s a lot more that will be...
  2. Misc. Jeep Parts
    FREE: Emission Air Pump off ‘79 CJ5 304 V8 3-speed. Frame Tie In Brackets & Bolts. 3-Speed Shifter Knob Screw On - Was on T150 3-Speed Shifter. Whatever else I find. Ships to Continental USA - Lower 48. Buyer pays Shipping.
    $1 USD
  3. Rancho Suspension
    Attention Jeep Wrangler JL owners, you spoke and we listened! Introducing Rancho's JL E-Brake Line Relocation Bracket. It is designed to retain the brake lines when rerouting under the cross member. Relocation is necessary if you have installed an extended travel suspension system. All necessary...
  4. Vendor Display
    JK owners!!! We have taken our tried and true geometry correction brackets for the JK platform and add even more options for castor with 4 holes. Our one piece design makes install incredibly easy. No need to fumble around with plates! You asked for it and we listened! Check with your favorite...
  5. Vendor Display
    We have just launched our new ADJUSTABLE front and rear track bars, center your axle easily with these adjustable track bars using our D2 rebuidable bushings. Our D2 bushings do an amazing job of absorbing road vibrations. Made with 1.25" OD diameter DOM for handling what is thrown at it. Check...
  6. ZJ Grand Cherokee Forum
    So here's a procedure question. The stock lower control arm bracket got crunched (just like everyone else') and the replacements are on the way. Before I start hot gluing them in place do I need to worry about burning anything inside? If I can get my grubby little fingers in there to cut the...
  7. Jeep CJ Forum
    I am in the middle of a complete redo under the hood of my cj7. on my 1981 258, the power steering pump does not have a method of locking itself in place, it just floats between the dampener and the purge air pulleys. it is tensioned by the purge air belt, as in the purge air pump tensions 2...
  8. XJ Cherokee Technical Forum
    I have a 1987 cherokee pioneer w/ 4.0 ac 4x4 4 door wagon that I removed the engine and front end down to the frame, cleaned and painted everything, then put back together. I have (3) brackets (see photos) that I cannot seem to identify or locate what they are for or what they do. I got the...
  9. YJ Wrangler Technical Forum
    Hi everyone, I have a 92 yj and when I got it, it had some rust on the frame. Right where the shock absorber is in the rear. Finally my passenger side side broke where it connects to the axle. And on my other one it's about to break at the top where it connects to the frame of the jeep. Where...
  10. YJ Wrangler Technical Forum
    I bought some new seats but they sit too high, the brackets need to be lower. I need diimensions for lower seat brackets.
  11. Full Size Jeep Forum
    So I have searched hi and low for amc 360 power steering pump brackets, I was curious if anyone knows where you can get them maybe after market seems that the cast aluminum just doesn't hold up .
  12. Jeep CJ Forum
    Hey everybody, Need some help locating some power steering pump brackets for a AMC 304. My jeep is 90 percent complete from a frame off restoration, if anyone knows where I can find one I would appreciate the help.
  13. Jeep CJ Forum
    I have 82 CJ8 Scrambler and I just bought a spare tire carrier from a guy on craigslist but it came without the mounting brackets. Can anybody help me out?
  14. TJ Wrangler Technical Forum
    I bought a 98 TJ that only came with a hard top. I bought a soft top for it and it came with brackets that fit onto the back of the roll bar. There doesn't seem to be guide holes for it or anything so I'll need to drill some I guess. I don't even know which way is up when it comes to these...
  15. ZJ Grand Cherokee Forum
    I got some Hella 500ffs Christmas and I've been planning on mounting them on my bumper for quite some time. I can't though, for the life of me, find whether or not i can use the fog light brackets from the old style zjs on my 98. it seems there are holes pre-drilled on the crossmember that seem...
  16. XJ Cherokee Technical Forum
    A Frosty axle swap - Ford 8.8, Cowl Intake, York OBA, plus more Index Page 1 - Ford 8.8 axle swap, Shackle relocation brackets, Custom cowl intake, Misc updates Page 2 - Battery relocation, Rear fender trim(unfinished), Start of York OBA bracket, Exhaust bandaid fix, Engine compart wire clean...
  17. YJ Wrangler Technical Forum
    I recently relocated the mirrors on my YJ and I'll be fine without my doors this summer, but looking forward to winter I've been searching for a kit similar to the one Warrior products uses for the 2007-2011 JK to plug my factory mirror mount holes. After researching this for a week or so, I...
  18. Jeep CJ Forum
    Does anyone know where I can find the bracket that the rear tire carrier bolts to (on the inside of the tub) and the tail gate cable bolts to on the body for a cj8 scrambler? The jeep was missing them when I bought it.
  19. Fabrication Shop
    Had a project fall through last minute and now have the complete ARB front bumper mounts and hardware for a WJ. I was in the process of fab'in a custom bumper and used ARB mounts to make sure everything lined up correctly and more importantly, STRONG. But now dont need these and cant return...
  20. General Jeep & Off-Road Equipment
    I just purchased a soft top for my 2005 Lj and wanted to verify parts that I need to complete the job. I know I need roll bar brackets (part #11) and screws (part #12) , and two knuckles (part #22) for the bows to attach to these brackets. How do the knuckles attach to the bows? Do I need...
1-20 of 28 Results
Top