JeepForum.com - Search Results
Advanced Search
Showing results 1 to 20 of 250
Search took 0.06 seconds.
Search: Posts Made By: Erbo1Kanerbo
Jeep Forums: Jeeps For Sale   06-13-2018, 06:50 PM
Replies: 1
Views: 1,557
Posted By Erbo1Kanerbo
Tires are basically new. Less than 3,000 miles on...

Tires are basically new. Less than 3,000 miles on them purchased in February 2018
Jeep Forums: Jeeps For Sale   06-13-2018, 06:49 PM
Replies: 1
Views: 1,557
Posted By Erbo1Kanerbo
2004 Lifted Grand Cherokee

FOR SALE: $8,000 OBO
2004 Jeep Grand Cherokee Special Edition
- 4.0L Engine
- 165k Miles
- 6.5" Long arm suspension
- Bilstein 5100 shocks
- Addco rear swaybar (not installed)
- Clayton...
Jeep Forums: Grand Cherokee General Discussion   06-12-2016, 09:21 AM
Replies: 6
Views: 678
Posted By Erbo1Kanerbo
Let's see a Wj flipped over

Let's see a Wj flipped over
Jeep Forums: WJ Grand Cherokee Forum   06-06-2016, 10:17 PM
Replies: 56
Views: 2,755
Posted By Erbo1Kanerbo
Nice job...small tip if you ever have to do it...

Nice job...small tip if you ever have to do it again you can freeze your pinion or carrier and it makes pressing on bearings or ring gear really easy if you don't have the proper tools
Jeep Forums: WJ Grand Cherokee Forum   06-05-2016, 08:14 AM
Replies: 49,173
Views: 4,509,835
Posted By Erbo1Kanerbo
Replacing my water pump. What a son of a ******!

Replacing my water pump. What a son of a ******!
Jeep Forums: Jeep Picture Requests   06-05-2016, 08:10 AM
Replies: 4,882
Views: 864,426
Posted By Erbo1Kanerbo
Wj long arm flex

Wj long arm flex
Jeep Forums: Grand Cherokee General Discussion   06-03-2016, 07:57 AM
Replies: 26
Views: 1,818
Posted By Erbo1Kanerbo
Looks phresh with the color match! FYI you can...

Looks phresh with the color match! FYI you can get that faded cladding back to black with a heat gun or torch.
Jeep Forums: WJ Grand Cherokee Forum   06-02-2016, 08:47 PM
Replies: 49,173
Views: 4,509,835
Posted By Erbo1Kanerbo
Yeah I actually relocated my front shocks which...

Yeah I actually relocated my front shocks which made the shocks I had too long. It was a spur of the moment decision I made the night before I went off-road.I had my jeep on an rti ramp today and I...
Jeep Forums: WJ Grand Cherokee Forum   05-30-2016, 09:32 PM
Replies: 56
Views: 2,755
Posted By Erbo1Kanerbo
Pinion preload is set without the carrier...

Pinion preload is set without the carrier installed...there is a spec for total torque to rotate which is the measurement with the carrier installed but I just put enough shims in to where I have to...
Jeep Forums: WJ Grand Cherokee Forum   05-30-2016, 09:00 PM
Replies: 56
Views: 2,755
Posted By Erbo1Kanerbo
Make sure the splines on the yoke and pinion are...

Make sure the splines on the yoke and pinion are clean and straight. Not sure what else to tell ya. I use an air impact to tighten the pinion nut that draws the yoke onto the pinion. Then I tighten...
Jeep Forums: WJ Grand Cherokee Forum   05-30-2016, 07:01 PM
Replies: 10
Views: 705
Posted By Erbo1Kanerbo
X2 on the swivel socket

X2 on the swivel socket
Jeep Forums: WJ Grand Cherokee Forum   05-30-2016, 06:59 PM
Replies: 127
Views: 54,726
Posted By Erbo1Kanerbo
I've pulled a couple at junkyards to...

I've pulled a couple at junkyards to practice...I've only been able to get one bezel off without focking up something lol
Jeep Forums: WJ Grand Cherokee Forum   05-30-2016, 06:57 PM
Replies: 1
Views: 502
Posted By Erbo1Kanerbo
Driveshaft could be out of phase...try turning it...

Driveshaft could be out of phase...try turning it 180 then reinstall and try on both ends tcase and axle to see if it changes at all. You could take it out and get it balanced. Just to rule out the...
Jeep Forums: WJ Grand Cherokee Forum   05-30-2016, 06:36 PM
Replies: 56
Views: 2,755
Posted By Erbo1Kanerbo
I hold the yoke with my left hand and my right...

I hold the yoke with my left hand and my right hand air hammers the face of the pinion (it has an indent on it for that reason). If you don't have an air hammer have a buddy push in on the pinion...
Jeep Forums: WJ Grand Cherokee Forum   05-30-2016, 06:06 PM
Replies: 56
Views: 2,755
Posted By Erbo1Kanerbo
Your right been a while since I've seen...

Your right been a while since I've seen that...haven't really payed attention to mine. I've mostly done JK's
Jeep Forums: WJ Grand Cherokee Forum   05-30-2016, 04:56 PM
Replies: 56
Views: 2,755
Posted By Erbo1Kanerbo
Most kits I've seen come with two crush sleeves...

Most kits I've seen come with two crush sleeves never seen two pinion seals. It looks like the one on the right has an oil slinger stuck to it
Jeep Forums: WJ Grand Cherokee Forum   05-30-2016, 04:55 PM
Replies: 56
Views: 2,755
Posted By Erbo1Kanerbo
For new bearings on a 30 I set them between 12-15...

For new bearings on a 30 I set them between 12-15 in/lbs...that one on the right has an oil slinger stuck to it take it off
Jeep Forums: WJ Grand Cherokee Forum   05-30-2016, 04:39 PM
Replies: 56
Views: 2,755
Posted By Erbo1Kanerbo
I have used pinion bearings I use as setup...

I have used pinion bearings I use as setup bearings that work fine...pattern never changes. Done well over 30 jeeps that way. Like said above if your not replacing the ring and pinion reuse the same...
Jeep Forums: WJ Grand Cherokee Forum   05-30-2016, 04:22 PM
Replies: 49,173
Views: 4,509,835
Posted By Erbo1Kanerbo
Took the jeep out off-road and broke a shock and...

Took the jeep out off-road and broke a shock and dropped a coil a few times. Next on the list is some correct length shocks and coil retainers
Jeep Forums: WJ Grand Cherokee Forum   05-29-2016, 11:53 AM
Replies: 56
Views: 2,755
Posted By Erbo1Kanerbo
Are you replacing the ring and pinion? Or just...

Are you replacing the ring and pinion? Or just the carrier bearings?
Showing results 1 to 20 of 250

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome