JeepForum.com - Search Results
Advanced Search
Showing results 1 to 13 of 13
Search took 0.02 seconds.
Search: Posts Made By: lakelotman2
Jeep Forums: YJ Wrangler Technical Forum   05-29-2019, 07:45 AM
Replies: 6
Views: 419
Posted By lakelotman2
YJ Ignition conversion to MSD

90 YJ 4.2 bypassed computer installed MSD distributor years ago, Then last year she needed a new alternator and yep I probably picked the one with most amp out. So the charge is going to the ignition...
Jeep Forums: YJ Wrangler Technical Forum   07-03-2018, 09:54 AM
Replies: 230
Views: 122,200
Posted By lakelotman2
Did My 90 when this thread first started would...

Did My 90 when this thread first started would have went smoothly if I had not put the flywheel in backwards then paid someone else 1500 to fix it and also take apart the steering wheel, ignition and...
Jeep Forums: YJ Wrangler Technical Forum   02-24-2016, 08:41 AM
Replies: 230
Views: 122,200
Posted By lakelotman2
Didn't look through all the after post but...

Didn't look through all the after post but conserning the external slave swap which I did, [I] also put the master/ slave pre bled single unit in as opposed to dealing with bleeding them ... this was...
Jeep Forums: Transmissions   02-02-2016, 01:29 PM
Replies: 76
Views: 22,320
Posted By lakelotman2
we put a 95 belhousing and an outside slave on...

we put a 95 belhousing and an outside slave on this when we put the last clutch, just don't put the clutch plate in backwards or else you will need a new flywheel like I did.
Jeep Forums: Carburetors   02-02-2016, 01:26 PM
Replies: 19
Views: 7,121
Posted By lakelotman2
We replace the oem carb since we went through 2...

We replace the oem carb since we went through 2 oem and still would not run right we removed the computer and put the weber carb on and no problems since.
Jeep Forums: YJ Wrangler Technical Forum   02-02-2016, 11:31 AM
Replies: 2
Views: 472
Posted By lakelotman2
What engines can I bolt up to my YJ AX

Now that I have the new clutch with the slave on the outside swap working good, and new radiator, hoses thirmister, computer bypassed different carb on my 4.2 changed plugs but now after it runs a...
Jeep Forums: YJ Wrangler Technical Forum   09-11-2015, 02:20 PM
Replies: 230
Views: 122,200
Posted By lakelotman2
I have the exact same issue going from 90 to 95 swap

I did the same thing and got the exact same issue only difference I didn't replace the flywheel I was wondering it there is serface rust on the flywheel and the clutch is stuck to it?

My next...
Jeep Forums: YJ Wrangler Technical Forum   09-03-2015, 07:38 AM
Replies: 230
Views: 122,200
Posted By lakelotman2
I think the master will be ok although too short,...

I think the master will be ok although too short, but the slave is my issue, which I plan to turnbuckle an extention to it
Jeep Forums: YJ Wrangler Technical Forum   08-31-2015, 08:21 AM
Replies: 230
Views: 122,200
Posted By lakelotman2
I had to modify the master to fit the bolt...

I had to modify the master to fit the bolt pattern and had to drill a hole in the peddle and use a bolt and nuts to get the new master to align correctly, but it is even with the break. just wish I...
Jeep Forums: YJ Wrangler Technical Forum   08-28-2015, 09:51 AM
Replies: 230
Views: 122,200
Posted By lakelotman2
With my swap I put a 95 clutch and bellhousing in...

With my swap I put a 95 clutch and bellhousing in my 90 wrangler. now I am hoping the 96 xj is the same as 95 I think I am going to buy a master/slave for the 96 and hope it fits
Jeep Forums: YJ Wrangler Technical Forum   08-28-2015, 06:54 AM
Replies: 230
Views: 122,200
Posted By lakelotman2
This sounds right Mikey, there were no spacer on...

This sounds right Mikey, there were no spacer on the salve, I did try to put a short 1/2" socket on the end of the pushrod of the slave which should have gave it about a 1/2" further push but still...
Jeep Forums: YJ Wrangler Technical Forum   08-27-2015, 07:40 AM
Replies: 230
Views: 122,200
Posted By lakelotman2
Ok I did the external swap but everything fit...

Ok I did the external swap but everything fit good looked good but when I finished the clutch does not release all the way or enough to slip. the only thing I did different was buy a master slave...
Jeep Forums: YJ Wrangler Technical Forum   05-12-2015, 09:24 AM
Replies: 16
Views: 4,836
Posted By lakelotman2
Me too having trouble finding an bellhousing to fit AX 15 to 4.0

Any idea where to find the bellhousing? need 95 or up with AX15 for external slave swap
Showing results 1 to 13 of 13

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome