JeepForum.com - Search Results
Advanced Search
Showing results 1 to 20 of 39
Search took 0.01 seconds.
Search: Posts Made By: RLPII
Jeep Forums: Jeep CJ Forum   07-09-2015, 04:19 PM
Replies: 39
Views: 2,145
Posted By RLPII
I'm no expert on these things but I have had...

I'm no expert on these things but I have had nothing but problems with the Edelbrock on the 360 and have been successful with the Holley. Vacuum leaks can certainly cause a lot of issues. Search...
Jeep Forums: Jeep CJ Forum   07-08-2015, 10:32 PM
Replies: 39
Views: 2,145
Posted By RLPII
I have a 74 CJ-5 with the AMC 360. Had the same...

I have a 74 CJ-5 with the AMC 360. Had the same problem with the Edelbrock (1405) Carb - I replaced the tank, sending unit, fuel lines, mechanical fuel pump, put a fuel pressure regulator and...
Jeep Forums: Jeep CJ Forum   06-11-2015, 11:36 PM
Replies: 2
Views: 687
Posted By RLPII
My bad, I was doing the post from memory and...

My bad, I was doing the post from memory and should know better :confused:, they are 2.5", not 2"! Sorry:o
Jeep Forums: Jeep CJ Forum   06-11-2015, 11:05 PM
Replies: 2
Views: 687
Posted By RLPII
Con-Fer Spring Plates?

I found a pair of Con-Ferr spring plates in a box in the garage. Started to clean them up to install on my 74 CJ5 and discovered that, apparently, they are for the 2" springs and not the 1.75"...
Jeep Forums: Jeep CJ Forum   03-13-2015, 09:00 AM
Replies: 8
Views: 812
Posted By RLPII
Thanks all.....some great info and...

Thanks all.....some great info and resources........truly appreciated.
Bob
Jeep Forums: Jeep CJ Forum   03-11-2015, 11:43 PM
Replies: 8
Views: 812
Posted By RLPII
Gearing and Lockers

My CJ has:
Front: Dana 30, 373 Gears, and a LockRite Locker
Rear: Dana 44, 373 Gears, and a Power Trax - No Slip Locker

I want to go to lower gears, maybe 488's or 427's at the very least. My...
Jeep Forums: Jeep CJ Forum   02-19-2015, 11:28 PM
Replies: 7
Views: 1,640
Posted By RLPII
Thanks for all the info and comments.....sounds...

Thanks for all the info and comments.....sounds like the hydraulic is the way to go. Will need to do some research so might be awhile! :)
Bob
Jeep Forums: Jeep CJ Forum   02-19-2015, 08:19 AM
Replies: 7
Views: 1,640
Posted By RLPII
should be "convert the linkage"

should be "convert the linkage"
Jeep Forums: Jeep CJ Forum   02-19-2015, 08:18 AM
Replies: 7
Views: 1,640
Posted By RLPII
The more I look into the cable idea the less I...

The more I look into the cable idea the less I like it.....lots of breakage. So, how about the hydraulic clutch set ups, any thoughts on that? Does anyone make a "Kit" to confront the linkage to...
Jeep Forums: Jeep CJ Forum   02-18-2015, 11:15 PM
Replies: 7
Views: 1,640
Posted By RLPII
Cable Clutch Conversion?

I am considering converting my 74 CJ5 (AMC 360) to a cable clutch to eliminate the clutch linkage binding up when the frame flexes. Does any one have a parts list or is there a kit available to make...
Jeep Forums: Jeep CJ Forum   02-08-2015, 07:38 AM
Replies: 0
Views: 661
Posted By RLPII
JB Fab Twin Stick - Dana 20

Just finished the install of the JB Twin Sticks on my Dana 20 (1974 CJ-5, 360 AMC and T-15). The product appears to be of excellent quality and the install was very easy. I did the install without...
Jeep Forums: Jeep CJ Forum   12-07-2014, 10:41 PM
Replies: 49
Views: 4,624
Posted By RLPII
Found the leak and everything appears to be...

Found the leak and everything appears to be working fine now. Not sure if I like the electric choke or not? So, might replace that with a manual choke. It passed the "garage test" for fuel...
Jeep Forums: Jeep CJ Forum   12-05-2014, 11:02 PM
Replies: 49
Views: 4,624
Posted By RLPII
Roger that..... I will check that out.............

Roger that..... I will check that out.......... man, always something! :)
Jeep Forums: Jeep CJ Forum   12-05-2014, 06:47 PM
Replies: 49
Views: 4,624
Posted By RLPII
Would the spacer have any affect on the idle...

Would the spacer have any affect on the idle speed? I finally fired it up this afternoon and I can't get it to idle less than about 1200-1500 RPM. (This is a guess because I have not hooked up my...
Jeep Forums: Jeep CJ Forum   12-03-2014, 09:03 PM
Replies: 49
Views: 4,624
Posted By RLPII
Its hard to see but there is a full...

Its hard to see but there is a full cage....reinforced floors and fender mountings. I am pretty sure that this will be a "project" for years to come!
Jeep Forums: Jeep CJ Forum   12-03-2014, 06:49 PM
Replies: 49
Views: 4,624
Posted By RLPII
Not sure if I did this right, but I think here is...

Not sure if I did this right, but I think here is a picture of my "project":
Jeep Forums: Jeep CJ Forum   12-03-2014, 05:32 PM
Replies: 49
Views: 4,624
Posted By RLPII
Yes, the electric pump is outside of the tank,...

Yes, the electric pump is outside of the tank, and I have located it on the inside of the frame, protected on 3 sides, right above the forward spring perch. Yes it does push, but a volume check...
Jeep Forums: Jeep CJ Forum   12-03-2014, 01:48 PM
Replies: 12
Views: 1,565
Posted By RLPII
Anyone have experience with the EZWiring harness?...

Anyone have experience with the EZWiring harness? http://www.ezwiring.com/wiring_harness.html
Jeep Forums: Jeep CJ Forum   12-03-2014, 11:37 AM
Replies: 49
Views: 4,624
Posted By RLPII
OK, so I now have the Holley fuel pump and just...

OK, so I now have the Holley fuel pump and just got my early Christmas present from the wife of the Holley Truck Avenger (670 CFM) carb.!:D

Since I do most of my wheeling at 5000 ft. elevation or...
Jeep Forums: Jeep CJ Forum   11-09-2014, 09:51 PM
Replies: 49
Views: 4,624
Posted By RLPII
I have decided to try the electric fuel pump and...

I have decided to try the electric fuel pump and a fuel pressure regulator. Picked up a Holley pump and regulator at Summit Racing and I hope to get it all installed this next week. Here's hoping!...
Showing results 1 to 20 of 39

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome