JeepForum.com - Search Results
Advanced Search
Showing results 1 to 20 of 250
Search took 0.05 seconds.
Search: Posts Made By: Rubi4MyMrs
Jeep Forums: TJ Wrangler Technical Forum   06-21-2021, 09:41 PM
Replies: 2
Views: 276
Posted By Rubi4MyMrs
I have seen leaking caps replaced. Even have some...

I have seen leaking caps replaced. Even have some links to them if needed.
Jeep Forums: TJ Wrangler Technical Forum   06-11-2021, 07:24 PM
Replies: 16
Views: 1,037
Posted By Rubi4MyMrs
Thanks mukluk. It’s interesting about...

Thanks mukluk.

It’s interesting about the flywheel. I guess they only really need one spot marking the 1/6 TDC to sync the cam, then use the 6 OPDA sets of notches to better sync & trigger...
Jeep Forums: TJ Wrangler Technical Forum   06-11-2021, 11:35 AM
Replies: 16
Views: 1,037
Posted By Rubi4MyMrs
The P0016 can come up from wear on either the...

The P0016 can come up from wear on either the timing chain/sprockets or wear/stretch or the cam/OPDA gears. The chain/sprockets is more “normal” wear. Either will retard the cam timing relative to...
Jeep Forums: TJ Wrangler Technical Forum   06-10-2021, 04:36 PM
Replies: 16
Views: 1,037
Posted By Rubi4MyMrs
In the links I posted he mentioned have it throw...

In the links I posted he mentioned have it throw codes above a certain which I havenít seen posted in the various 340/344 postings but thinking about that combined with a short dwell makes me thing...
Jeep Forums: TJ Wrangler Technical Forum   06-09-2021, 07:46 PM
Replies: 16
Views: 1,037
Posted By Rubi4MyMrs
A clarification: I have been looking at...

A clarification:

I have been looking at the scope shots of both sensors which I have not done in a long time. I see that it is not that the 5v pulse is too short on the aftermarket sensor it...
Jeep Forums: TJ Wrangler Technical Forum   06-09-2021, 06:11 PM
Replies: 16
Views: 1,037
Posted By Rubi4MyMrs
If I recall the PDF was in 4951 & the actual shot...

If I recall the PDF was in 4951 & the actual shot was in 4952. I think he made some reference to some not being able to open it so he posted it. If you don’t find it there let me know & I will copy...
Jeep Forums: TJ Wrangler Technical Forum   06-09-2021, 04:16 PM
Replies: 16
Views: 1,037
Posted By Rubi4MyMrs
Here is info that may be helpful. It is a bit...

Here is info that may be helpful. It is a bit dated but good info. The only update I can think of is that for some time now even the cam sensors from the dealers are giving the same problems so I...
Jeep Forums: TJ Wrangler Technical Forum   06-08-2021, 05:09 PM
Replies: 4
Views: 407
Posted By Rubi4MyMrs
I know what you mean about jschereb. He is a...

I know what you mean about jschereb. He is a tough act to follow. He has been asked (more then once, I’m sure) about making side windows that open, probably with a slider arrangement but he has...
Jeep Forums: TJ Wrangler Technical Forum   06-08-2021, 09:53 AM
Replies: 4
Views: 407
Posted By Rubi4MyMrs
What exactly are you looking for? They are odd...

What exactly are you looking for? They are odd shaped. The corners are rounded, the ends are not parallel, the top is rounded (curved) & the glass itself is not flat but convexed (is bulging outward...
Jeep Forums: TJ Wrangler Technical Forum   06-08-2021, 09:41 AM
Replies: 6
Views: 491
Posted By Rubi4MyMrs
Are you certain there is no harness damage behind...

Are you certain there is no harness damage behind the engine?

That harness has the wires from the intake manifold area (including the IAC, TPS, etc.) & probably the O2 sensors as well. That...
Jeep Forums: TJ Wrangler Technical Forum   06-03-2021, 09:16 PM
Replies: 6
Views: 501
Posted By Rubi4MyMrs
Unless the actual mode switch is bad, which is...

Unless the actual mode switch is bad, which is rare, you should be able to repair the wiring harness. Most simply cut the damaged connector off & using spade terminals crimped or soldered to each of...
Jeep Forums: TJ Wrangler Technical Forum   06-03-2021, 07:02 PM
Replies: 6
Views: 501
Posted By Rubi4MyMrs
Check the 3 wire connector on the back side of...

Check the 3 wire connector on the back side of the mode selector switch. That is a known place for the connector to melt from excessive heat & cause loss of grounding for both the blower (fan) & the...
Jeep Forums: TJ Wrangler Technical Forum   06-01-2021, 04:03 PM
Replies: 9
Views: 12,761
Posted By Rubi4MyMrs
This is an old post & the OP has not posted...

This is an old post & the OP has not posted anything since 2010 so not much chance he will respond & not much helpful info here but I have seen this, or something like it if you have the 2 actuator...
Jeep Forums: TJ Wrangler Technical Forum   05-26-2021, 04:03 PM
Replies: 11
Views: 756
Posted By Rubi4MyMrs
Hopefully you did not damage the trans when you...

Hopefully you did not damage the trans when you compressed the torque converter against the flex plate.

I’m not sure about that trans but on some that last converter engagement going in is...
Jeep Forums: TJ Wrangler Technical Forum   05-26-2021, 03:54 PM
Replies: 14
Views: 1,024
Posted By Rubi4MyMrs
You are not reading the diagrams correctly. ...

You are not reading the diagrams correctly.

See the 1st diagram in post 13. Fuse 10 (40A) powers the headlights both hi & lo beams through the circuit breaker then to the part of the...
Jeep Forums: TJ Wrangler Technical Forum   05-25-2021, 07:53 PM
Replies: 11
Views: 756
Posted By Rubi4MyMrs
Very good point. Do that before dropping the pan...

Very good point. Do that before dropping the pan etc.
Jeep Forums: TJ Wrangler Technical Forum   05-25-2021, 06:23 PM
Replies: 11
Views: 756
Posted By Rubi4MyMrs
Pounding on the top of the pistons will not get...

Pounding on the top of the pistons will not get it to turn over even under normal conditions unless maybe you hit them so hard you would probably damage the piston.

Drop the pan, unbolt the...
Jeep Forums: TJ Wrangler Technical Forum   05-24-2021, 12:30 PM
Replies: 10
Views: 787
Posted By Rubi4MyMrs
The blend door which controls the temp setting in...

The blend door which controls the temp setting in electric since 1999. As you turn the knob the blend door motor is supposed to move the door. It is probably stuck. The motor is under the dash more...
Jeep Forums: TJ Wrangler Technical Forum   05-23-2021, 07:59 PM
Replies: 14
Views: 1,024
Posted By Rubi4MyMrs
Its not the high beams that melt the switch. Itís...

Its not the high beams that melt the switch. Itís the fogs. The switch (on the end of the arm) has a small plastic part the moves the contacts open/closed (as I recall) which gets hot , melts & will...
Jeep Forums: TJ Wrangler Technical Forum   05-23-2021, 05:53 PM
Replies: 1
Views: 340
Posted By Rubi4MyMrs
You might be able to turn that next section shown...

You might be able to turn that next section shown where the cylinder fits which is called the actuator which is what actually turns the ignition switch. However, there is a good chance turning it...
Showing results 1 to 20 of 250

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome