JeepForum.com - Search Results
Advanced Search
Showing results 1 to 20 of 250
Search took 0.39 seconds.
Search: Posts Made By: Jim1611
Jeep Forums: Jeep CJ Forum   Yesterday, 11:53 AM
Replies: 27
Views: 1,502
Posted By Jim1611
I don't think you'll have any trouble selling it...

I don't think you'll have any trouble selling it as is and avoid the scrap yard. If you were closer I'd consider it myself!
Jeep Forums: Jeep CJ Forum   Yesterday, 10:21 AM
Replies: 20
Views: 638
Posted By Jim1611
Made this wrench for the headlight and wiper...

Made this wrench for the headlight and wiper switch nuts that attach them to the dash.
Jeep Forums: Full Size Jeep Forum   02-26-2020, 11:28 AM
Replies: 282
Views: 25,929
Posted By Jim1611
Dave it's good to hear that you're doing good and...

Dave it's good to hear that you're doing good and enjoying yourself. Keep at the health stuff and take care!
Jeep Forums: Jeep CJ Forum   02-25-2020, 05:00 PM
Replies: 10
Views: 238
Posted By Jim1611
John I did something like the piece of tape...

John I did something like the piece of tape measure. I took a copper strip about 1/6" thick then drilled a hole in it to go under one of the bolts that attach the upper housing to the metal tube....
Jeep Forums: Jeep CJ Forum   02-25-2020, 02:30 PM
Replies: 10
Views: 238
Posted By Jim1611
No it would not. I didn't think the upper housing...

No it would not. I didn't think the upper housing is plastic though but it very well could be. So I'm going to have to find a way to ground the main shaft.
Jeep Forums: Jeep CJ Forum   02-25-2020, 01:17 PM
Replies: 7
Views: 233
Posted By Jim1611
I have the dual Ford Contour fans on my CJ and...

I have the dual Ford Contour fans on my CJ and used a switch mounted inside the thermostat housing. It just completes the ground so the relays will engage and send power to the fans. This is on a...
Jeep Forums: Jeep CJ Forum   02-25-2020, 01:10 PM
Replies: 10
Views: 238
Posted By Jim1611
I painted the column and shaft with POR15 and...

I painted the column and shaft with POR15 and used an aftermarket bearing kit on the lower end. It's not likely grounding at the bottom end. So it won't ground through the top bearing? The top end of...
Jeep Forums: Jeep CJ Forum   02-25-2020, 11:55 AM
Replies: 10
Views: 238
Posted By Jim1611
I do have all the parts you've shown, John. And...

I do have all the parts you've shown, John. And in correctly. I took the steering wheel assembly off to check things out is when I tried grounding the shaft itself. I took the set screw out that...
Jeep Forums: Jeep CJ Forum   02-25-2020, 11:02 AM
Replies: 7
Views: 397
Posted By Jim1611
You can also take the lower steering shaft off of...

You can also take the lower steering shaft off of the end of the column shaft and pull the entire steering wheel and shaft out together then you could support the bottom of the steering wheel and use...
Jeep Forums: Jeep CJ Forum   02-25-2020, 09:16 AM
Replies: 10
Views: 238
Posted By Jim1611
Not getting a ground for the horn to work

I am not having any luck in getting my horn to work as it should. I've traced it back to the main steering shaft not being grounded. I can clamp a ground wire on the shaft and jump that to the spring...
Jeep Forums: Jeep CJ Forum   02-24-2020, 07:30 PM
Replies: 25,641
Views: 2,008,937
Posted By Jim1611
Looks good and functional. You carry a ladder to...

Looks good and functional. You carry a ladder to get in and out of that thing?
Jeep Forums: Jeep CJ Forum   02-24-2020, 07:28 PM
Replies: 7
Views: 233
Posted By Jim1611
I hear they work pretty good. I like the ones...

I hear they work pretty good. I like the ones that make contact with the coolant better though.
Jeep Forums: Jeep CJ Forum   02-23-2020, 09:12 PM
Replies: 104
Views: 5,451
Posted By Jim1611
You going to do all the welding with it bolted to...

You going to do all the welding with it bolted to the block?
Jeep Forums: Jeep CJ Forum   02-23-2020, 09:09 PM
Replies: 4,227
Views: 532,665
Posted By Jim1611
Thanks Mike. It has taken a while, hasn't it?...

Thanks Mike. It has taken a while, hasn't it? :grin2: A trip through the Rubicon with you would be great!


Thanks, my friend!
Jeep Forums: Jeep CJ Forum   02-23-2020, 09:01 PM
Replies: 689
Views: 114,152
Posted By Jim1611
Bob in my dealings with coating companies the...

Bob in my dealings with coating companies the better you can send them what you want chromed the less costly. So if you send your wheels somewhere to get them chromed you should make sure they're...
Jeep Forums: Jeep CJ Forum   02-22-2020, 09:16 PM
Replies: 197
Views: 13,175
Posted By Jim1611
You got it!

You got it!
Jeep Forums: Jeep CJ Forum   02-22-2020, 09:12 PM
Replies: 25,641
Views: 2,008,937
Posted By Jim1611
More aerodynamic. That and the tires should yield...

More aerodynamic. That and the tires should yield many more mpg :grin2:
Jeep Forums: Jeep CJ Forum   02-22-2020, 08:05 PM
Replies: 4,227
Views: 532,665
Posted By Jim1611
Exhaust is on. Not as quiet as I wanted but not...

Exhaust is on. Not as quiet as I wanted but not bad, if the skinny pedal is not applied too hard. The tail pipes might be a bit too long but I won't do anything about that until after I get the rear...
Jeep Forums: Jeep CJ Forum   02-22-2020, 07:51 PM
Replies: 6
Views: 232
Posted By Jim1611
There are some threads around here dealing with...

There are some threads around here dealing with different carburetors on the inline-6 so that's an option too and not too costly. I think it's the Autolite (Ford) 2100 that has been used quite a bit....
Jeep Forums: Jeep CJ Forum   02-21-2020, 08:00 PM
Replies: 2,909
Views: 308,547
Posted By Jim1611
Cool history and picture, Fred. Hey my fiberglass...

Cool history and picture, Fred. Hey my fiberglass hard top need a little work....wanna do some more glue sniffing? :grin2:
Showing results 1 to 20 of 250

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome