JeepForum.com - Search Results
Advanced Search
Showing results 1 to 20 of 250
Search took 0.93 seconds.
Search: Posts Made By: Zombi
Jeep Forums: TJ Wrangler Technical Forum   08-28-2014, 10:01 AM
Replies: 13
Views: 827
Posted By Zombi
Track bar is a custom heim joint jobber mounted...

Track bar is a custom heim joint jobber mounted on reinforced double sheer 3/16" mounts on both the axle side and frame side. Mounted as to match the drag link angle and spacing as much as possible....
Jeep Forums: TJ Wrangler Technical Forum   08-27-2014, 10:03 AM
Replies: 13
Views: 827
Posted By Zombi
Not only did I try it when set at 1/8", I tried...

Not only did I try it when set at 1/8", I tried with it at 1/16" before going for a toe setting that I could drive. Neither worked and made the Jeep completely undriveable. With either of those...
Jeep Forums: TJ Wrangler Technical Forum   08-27-2014, 09:12 AM
Replies: 13
Views: 827
Posted By Zombi
If the housing were bent, wouldn't it be chewing...

If the housing were bent, wouldn't it be chewing through unit bearings like crazy? Or wander like no tomorrow?
Also, wouldn't the wear be uneven left to right? To put some numbers to it, I get less...
Jeep Forums: TJ Wrangler Technical Forum   08-27-2014, 08:27 AM
Replies: 13
Views: 827
Posted By Zombi
Extreme tire wear and wobble after HP30 swap

This is getting out of hand here.

Back story: A few years ago I swapped in an HP30 out of a 2000 xj. Original factory brackets, no weld modifications to it. When I did the swap I replaced the...
Jeep Forums: TJ Wrangler Technical Forum   04-09-2014, 06:11 AM
Replies: 29
Views: 1,894
Posted By Zombi
I cheaped out and got the P.ORC version. I've...

I cheaped out and got the P.ORC version.
I've been through two output shaft seals and cannot get the damned thing to stop leaking.

I run a Tattons driveshaft off ebay and have nothing but good...
Jeep Forums: TJ Wrangler Technical Forum   04-04-2014, 12:02 PM
Replies: 1
Views: 402
Posted By Zombi
2000+ Manifold nut?

I've got the two piece manifold swapped onto my 99 and it just recently lost the bolts entirely.

I see a number of different parts out there that I never saw when I went to put these things...
Jeep Forums: TJ Wrangler Technical Forum   04-01-2014, 10:28 AM
Replies: 5
Views: 450
Posted By Zombi
Something upstream let loose inside the exhaust...

Something upstream let loose inside the exhaust perhaps?
Catalytic converter would be my guess.

How is performance and fuel consumption?
Jeep Forums: TJ Wrangler Technical Forum   03-28-2014, 01:07 PM
Replies: 17
Views: 1,448
Posted By Zombi
Like mentioned, disco the battery and keep that...

Like mentioned, disco the battery and keep that clamp close to the weld area.
I too have never had problems doing it that way.
Jeep Forums: TJ Wrangler Technical Forum   03-28-2014, 06:47 AM
Replies: 11
Views: 729
Posted By Zombi
Typically you'd want an 8" wide wheel, they offer...

Typically you'd want an 8" wide wheel, they offer more protection of the wheel itself.
You can run a 10.5" tire on them if you wanted to without any issues.
The tires tend to look like a...
Jeep Forums: TJ Wrangler Technical Forum   03-27-2014, 06:51 AM
Replies: 11
Views: 729
Posted By Zombi
It will probably rub. 3.75"-4" is...

It will probably rub.
3.75"-4" is ideal.
Jeep Forums: TJ Wrangler Technical Forum   03-25-2014, 12:09 PM
Replies: 3
Views: 423
Posted By Zombi
You might have better luck in the fabrication...

You might have better luck in the fabrication section:

https://www.jeepforum.com/forum/f37/
Jeep Forums: TJ Wrangler Technical Forum   03-24-2014, 01:58 PM
Replies: 10
Views: 661
Posted By Zombi
If it's in good shape and setup for a TJ, hell...

If it's in good shape and setup for a TJ, hell yea it's a good deal.
Jeep Forums: TJ Wrangler Technical Forum   03-21-2014, 01:00 PM
Replies: 1
  lifters
Views: 269
Posted By Zombi
They're hydraulic lifters. Chances are the...

They're hydraulic lifters. Chances are the internal tolerances have loosened up allowing the internal pressure to "bleed out".
What you're hearing is the lifter slapping around while the engine is...
Jeep Forums: TJ Wrangler Technical Forum   03-21-2014, 11:26 AM
Replies: 11
Views: 1,261
Posted By Zombi
I can't think of any pro's of 33's on JK wheels...

I can't think of any pro's of 33's on JK wheels vs 33's on TJ wheels besides possibly the look.
Ok, maybe the ability to run a bigger brake setup for 17" wheels might make this swap more appealing....
Jeep Forums: TJ Wrangler Technical Forum   03-21-2014, 11:15 AM
Replies: 5
Views: 2,425
Posted By Zombi
Right here, you can see it on the hood brace: ...

Right here, you can see it on the hood brace:
http://image.fourwheeler.com/f/9311378+w600+re0/154_0608_03_z%2B2004_jeep_wrangler_sport%2Bunder_hood.jpg

Same here: ...
Jeep Forums: Wrangler General Discussion   03-21-2014, 10:23 AM
Replies: 34
Views: 2,449
Posted By Zombi
I drilled my own drain holes in the rear LCA...

I drilled my own drain holes in the rear LCA area.
Frame still rotted through on both sides.
I had to use those "AutoRust" pieces to put it all back together.
Jeep Forums: Wrangler General Discussion   03-21-2014, 10:21 AM
Replies: 275
Views: 26,389
Posted By Zombi
I wouldn't be able to afford one anyway so it...

I wouldn't be able to afford one anyway so it doesn't matter to me.
Hell, I can't even afford a first year JK.
Jeep Forums: TJ Wrangler Technical Forum   03-14-2014, 02:42 PM
Replies: 7
Views: 547
Posted By Zombi
And sort of movement whatsoever besides the...

And sort of movement whatsoever besides the typical rotational movement a u-joint is supposed to provide.

If this axle had been sitting around outside of a vehicle for any length of time, you...
Jeep Forums: TJ Wrangler Technical Forum   03-14-2014, 07:12 AM
Replies: 3
Views: 430
Posted By Zombi
] You can rebuild those and put stiffer...

]

You can rebuild those and put stiffer springs in them as a cheaper alternative.
Jeep Forums: Wrangler General Discussion   03-13-2014, 01:00 PM
Replies: 3
Views: 459
Posted By Zombi
Nothing really, it's just insulation to keep heat...

Nothing really, it's just insulation to keep heat and noise out of the passenger compartment.
Showing results 1 to 20 of 250

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome