JeepForum.com - Search Results
Advanced Search
Showing results 1 to 20 of 20
Search took 0.01 seconds.
Search: Posts Made By: bluwavguy
Jeep Forums: Jeep CJ Forum   12-03-2015, 09:16 AM
Replies: 46
Views: 2,676
Posted By bluwavguy
Matt, Thanks, the jet that comes with the 2300...

Matt,
Thanks, the jet that comes with the 2300 350 cfm street avenger is 061 so I ordered the 058 and as recommended by Orange150 ordered the fast kit as well.
Brian
Jeep Forums: Jeep CJ Forum   12-03-2015, 08:05 AM
Replies: 46
Views: 2,676
Posted By bluwavguy
Orange/Sireland, Thank you for your advice. Ok...

Orange/Sireland,
Thank you for your advice. Ok on the Cam. I'll check the cam arm to the accel pump as well. I plan to call Holley later today to buy the .025 nozzle (currently have the .031 and...
Jeep Forums: Jeep CJ Forum   12-02-2015, 07:04 AM
Replies: 46
Views: 2,676
Posted By bluwavguy
Matt/Shawn, thank you. As I see it...the ...

Matt/Shawn, thank you.
As I see it...the smaller jet, down sizing of the accelerator pump nozzle will be next phase of tuning. As far as the accelerator pump cam on the throttle linkage, if the...
Jeep Forums: Jeep CJ Forum   12-01-2015, 10:08 AM
Replies: 46
Views: 2,676
Posted By bluwavguy
Shawn, As an after thought on the idle-feed....

Shawn, As an after thought on the idle-feed. Assume the mixture needs to be on the lean side would assume the needles should be around 3/4 to 1 1/4 out which is where they have been set most of the...
Jeep Forums: Jeep CJ Forum   12-01-2015, 09:48 AM
Replies: 46
Views: 2,676
Posted By bluwavguy
Shawn, Thank you. Resetting the timing was key....

Shawn,
Thank you. Resetting the timing was key. By Matt, I checked the bowl vent and with my finger on it could not get the engine to shut down.
I'll follow your recommendation. I've been setting...
Jeep Forums: Jeep CJ Forum   12-01-2015, 08:42 AM
Replies: 46
Views: 2,676
Posted By bluwavguy
Matt, the other thing I learned today is I'm at...

Matt, the other thing I learned today is I'm at 3800' elevation therefore Holley recommends a 1 size drop in jet size per 2000 ft elevation.
Holley tech got back to me and says they don't have...
Jeep Forums: Jeep CJ Forum   12-01-2015, 07:44 AM
Replies: 46
Views: 2,676
Posted By bluwavguy
Matt, according to Holley's web site on the PV,...

Matt, according to Holley's web site on the PV, the PV should be 1/2 the vacuum at idle. Thanks for the testing...doubt I'll get to it for a few days.
Jeep Forums: Jeep CJ Forum   12-01-2015, 07:04 AM
Replies: 46
Views: 2,676
Posted By bluwavguy
Matt, thanks. Any way for me to check the...

Matt, thanks.
Any way for me to check the power valve?
I sent the Holley Tech, who's been helping me on the rmp issue vs choke setting, a question related to the application specific settings for...
Jeep Forums: Jeep CJ Forum   12-01-2015, 06:17 AM
Replies: 46
Views: 2,676
Posted By bluwavguy
Mike, I now understand the purpose of the ICM and...

Mike, I now understand the purpose of the ICM and green wire. 1) I don't believe I have a ballast resistor on the new coil. 2) At this time I turn off the ignition switch. I'll investigate the...
Jeep Forums: Jeep CJ Forum   11-30-2015, 07:11 PM
Replies: 46
Views: 2,676
Posted By bluwavguy
Greatly appreciated. I'll check the vid out and...

Greatly appreciated. I'll check the vid out and besides the power valve this is one item I've yet to touch out of the box.
Thank you, Brian
Jeep Forums: Jeep CJ Forum   11-30-2015, 06:17 PM
Replies: 46
Views: 2,676
Posted By bluwavguy
All, I've got one of the rpm issues resolved...

All,

I've got one of the rpm issues resolved as the Holley Electric Choke was not adjusted properly and now fully opening and the fast idle linkage kicks out.

Best Vacuum I can achieve is about...
Jeep Forums: Jeep CJ Forum   11-21-2015, 06:50 AM
Replies: 46
Views: 2,676
Posted By bluwavguy
John, thank you. I had one of those in my hand...

John, thank you. I had one of those in my hand yesterday at the store but was on track to port it to the air filter.
I'll get that along with the PCV that was ordered and arrives to the part store...
Jeep Forums: Jeep CJ Forum   11-20-2015, 04:44 PM
Replies: 46
Views: 2,676
Posted By bluwavguy
Jeepwhore, got it. My bad on my notes as I meant...

Jeepwhore, got it. My bad on my notes as I meant to say as you noted in item 2. That was my question to the guy in the parts shop who was clueless. Can I just install a breather filter (eldelbrock...
Jeep Forums: Jeep CJ Forum   11-20-2015, 12:15 PM
Replies: 46
Views: 2,676
Posted By bluwavguy
Matt, greatly appreciated. I'm heading down to...

Matt, greatly appreciated. I'm heading down to the autoparts store to see what they have off the shelf.
The bottom of my air filter has a cut out to attach a line to the pvc breather.
I'll install...
Jeep Forums: Jeep CJ Forum   11-20-2015, 11:28 AM
Replies: 46
Views: 2,676
Posted By bluwavguy
John, for simplicity I'm attaching images of the...

John, for simplicity I'm attaching images of the system as is from a few min ago.

As shown the rear vent goes to the carb and the fwd vent is capped. The PO left it open to the air.
The second...
Jeep Forums: Jeep CJ Forum   11-20-2015, 07:23 AM
Replies: 46
Views: 2,676
Posted By bluwavguy
Mike, thank you. I'll locate the appropriate...

Mike, thank you. I'll locate the appropriate parts to set this up.
Jeep Forums: Jeep CJ Forum   11-19-2015, 06:24 PM
Replies: 46
Views: 2,676
Posted By bluwavguy
Matt, its the 3/8" vent line from the valve cover...

Matt, its the 3/8" vent line from the valve cover (which has two ports of which I've capped one), and the 2nd is connected to the carb port (closest to the firewall).

Actually, I've reconnected...
Jeep Forums: Jeep CJ Forum   11-19-2015, 09:49 AM
Replies: 46
Views: 2,676
Posted By bluwavguy
Mike and others. I plugged the valve cover...

Mike and others.
I plugged the valve cover inlet to the carb, re-adjusted the idle mixture, and added a heavy duty throttle return spring (this is why my idle was so high).
Vacuum is around 17"...
Jeep Forums: Jeep CJ Forum   11-18-2015, 06:48 PM
Replies: 46
Views: 2,676
Posted By bluwavguy
Matt will do so or take it to my friend's...

Matt will do so or take it to my friend's commercial mechanics shop.

Orange150. In 2x2 she runs great in 1&2nd gears...depending on the grade 3rd and 4th are sluggish. In 4x4L the carb performs...
Jeep Forums: Jeep CJ Forum   11-18-2015, 02:54 PM
Replies: 46
Views: 2,676
Posted By bluwavguy
Cj Vacuum, RPM, and Carb Tuning

On a recent post I had a lot of good feedback and hoping to hear more.

Following JeepHammers post I upgraded the larger distributor and rotor. The Accel 8mm wires were brand new so I kept them on...
Showing results 1 to 20 of 20

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome