JeepForum.com - Search Results
Advanced Search
Showing results 1 to 20 of 250
Search took 0.03 seconds.
Search: Posts Made By: Stryker777
Jeep Forums: Advanced Jeep Tech   03-27-2019, 04:19 PM
Replies: 4
Views: 1,776
Posted By Stryker777
Thank you for the information. Thankfully, I am...

Thank you for the information. Thankfully, I am not using either vehicle. I'm not starting the conversion till July or early August. I didn't think about the throttle cable. I'll measure travel on...
Jeep Forums: Advanced Jeep Tech   03-26-2019, 10:07 AM
Replies: 4
Views: 1,776
Posted By Stryker777
Looking at the JB NP241C HD SUPER SHORT SYE...

Looking at the JB NP241C HD SUPER SHORT SYE w/1310 CV Yoke for the SYE. Wondering what will have to happen for the front shaft.
Jeep Forums: Advanced Jeep Tech   03-26-2019, 07:27 AM
Replies: 4
Views: 1,776
Posted By Stryker777
After some research, I see I don't want to reuse...

After some research, I see I don't want to reuse the NP207 from the YJ anyway so I will be using the NP241c. Now to pick the SYE and what driveshafts to use. I'm going to swap the speedometer to...
Jeep Forums: TJ Wrangler Technical Forum   03-25-2019, 06:16 PM
Replies: 1
  Np241c
Views: 279
Posted By Stryker777
I'm getting mine ready to do too. Interested to...

I'm getting mine ready to do too. Interested to see what others have done.
Jeep Forums: Advanced Jeep Tech   03-25-2019, 05:07 PM
Replies: 4
Views: 1,776
Posted By Stryker777
'87 YJ 4.2 to 5.7 700r4 Advice

I have a 92 GMC Z71 I'm about to pull from and drop in my 87 YJ. I can keep my Jeep transfer case and buy an adapter, or I think I can use the Chevy NP241c that is in the Z71. Both transfer cases...
Jeep Forums: YJ Wrangler Technical Forum   08-13-2016, 08:26 PM
Replies: 36
Views: 1,504
Posted By Stryker777
Thank you for the reply. I am leaning towards...

Thank you for the reply. I am leaning towards this option. I dont mind redoing the bottom end but there could be so many things he did not do right. I think I'll buy a new one, then rebuild this...
Jeep Forums: YJ Wrangler Technical Forum   08-13-2016, 04:35 PM
Replies: 36
Views: 1,504
Posted By Stryker777
Thanks for the info. Chrisnvegas, do you...

Thanks for the info. Chrisnvegas, do you remember how much it cost you total? You put in a 4.7 correct? Carbed?
Thanks
Jeep Forums: YJ Wrangler Technical Forum   08-13-2016, 01:32 PM
Replies: 36
Views: 1,504
Posted By Stryker777
I put a wrench on it and turned the crank shaft...

I put a wrench on it and turned the crank shaft till I had the strongest reading. I went through several cycles to verify. It was coming from the crank case. Lots of pressure from the breather.
Jeep Forums: YJ Wrangler Technical Forum   08-13-2016, 12:11 PM
Replies: 36
Views: 1,504
Posted By Stryker777
I finally got time to do the leak down test. ...

I finally got time to do the leak down test. Dropped my daughter off at her college yesterday and did the test today. Good news is 1,2,3,4,6 all had less than 20%. Bad news, cylinder 5 had 80%...
Jeep Forums: YJ Wrangler Technical Forum   08-10-2016, 08:29 AM
Replies: 36
Views: 1,504
Posted By Stryker777
Quick update. I have not had time to do the...

Quick update. I have not had time to do the leakdown test. The PO told me he did not machine the head because it was good. The cylinders just needed to be honed. I take my daughter to college...
Jeep Forums: YJ Wrangler Technical Forum   08-08-2016, 07:56 AM
Replies: 36
Views: 1,504
Posted By Stryker777
Good morning. I have the receipts for the rings. ...

Good morning. I have the receipts for the rings. Waiting on a reply from the PO about machining. This afternoon the gauges will come in and I will do a leak down test. Thanks again for the help.
Jeep Forums: YJ Wrangler Technical Forum   08-08-2016, 06:11 AM
Replies: 36
Views: 1,504
Posted By Stryker777
Here is a video of the blowby. There is also...

Here is a video of the blowby. There is also faint smoke from the exhaust during this.
https://youtu.be/GA3kbeEF9Ns
Jeep Forums: YJ Wrangler Technical Forum   08-06-2016, 02:29 PM
Replies: 36
Views: 1,504
Posted By Stryker777
You were right to question the bypass. I checked...

You were right to question the bypass. I checked and it was not done. It has been done now, timing and carb adjusted, and spark plugs replaced. The carb screws are within range. It sounds pretty...
Jeep Forums: YJ Wrangler Technical Forum   08-05-2016, 07:43 PM
Replies: 36
Views: 1,504
Posted By Stryker777
I am not sure that the nutter has been done. I...

I am not sure that the nutter has been done. I will verify it. I was told it was but so far there have been many things wrong that were not supposed to be. It has a weber 32/36 on it and pressure...
Jeep Forums: YJ Wrangler Technical Forum   08-05-2016, 06:53 PM
Replies: 36
Views: 1,504
Posted By Stryker777
Another update. Wet test was about 10psi higher...

Another update. Wet test was about 10psi higher on all cylinders. I couldn't get a leak down done. Storms are here for the rest of the evening. However, after setting the timing, the knock went...
Jeep Forums: YJ Wrangler Technical Forum   08-04-2016, 06:07 AM
Replies: 36
Views: 1,504
Posted By Stryker777
Thank you for the links! Especially that last...

Thank you for the links! Especially that last one. That has a lot of the info I have been trying to find. Much appreciated.
Jeep Forums: YJ Wrangler Technical Forum   08-04-2016, 05:12 AM
Replies: 36
Views: 1,504
Posted By Stryker777
Dancytron, I am guessing stock distributor. I...

Dancytron, I am guessing stock distributor. I have not compared it to find out. I'll check it out when I get off work.

TheDonk, I did not do a wet test. How much oil do I put in for a wet test?...
Jeep Forums: YJ Wrangler Technical Forum   08-03-2016, 08:42 PM
Replies: 36
Views: 1,504
Posted By Stryker777
I feel stupid now. I just got this Jeep a couple...

I feel stupid now. I just got this Jeep a couple weeks ago and did not check the timing. It was way off. With vacuum disconnected and at 800rpms, it was running at 23 or so btdc. I set it to 8...
Jeep Forums: YJ Wrangler Technical Forum   08-02-2016, 03:25 AM
Replies: 36
Views: 1,504
Posted By Stryker777
Plugs on 5 and 6 are fouled. I checked my vacuum...

Plugs on 5 and 6 are fouled. I checked my vacuum routing. I have the weber 32/36 carb. PCV is ran to the intake port near 5 and 6. I'm not happy with that because any oil would go straight in there....
Jeep Forums: YJ Wrangler Technical Forum   08-01-2016, 05:23 AM
Replies: 36
Views: 1,504
Posted By Stryker777
I agree about the plugs. I will swap them. I...

I agree about the plugs. I will swap them. I need to look at them anyway to see if they have any abnormal burn or oil. He put them in a couple months ago. I'll post an update Tuesday or Wednesday...
Showing results 1 to 20 of 250

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome