JeepForum.com - Search Results
Advanced Search
Showing results 1 to 20 of 22
Search took 0.01 seconds.
Search: Posts Made By: TDENXJ
Jeep Forums: Suspension Parts   07-15-2021, 09:52 PM
Replies: 3
Views: 288
Posted By TDENXJ
I actually just sold the kit last night. Sorry...

I actually just sold the kit last night. Sorry for late response.
Jeep Forums: Suspension Parts   07-07-2021, 09:18 PM
Replies: 3
Views: 288
Posted By TDENXJ
Located in southern ID

Located in southern ID
Jeep Forums: Suspension Parts   07-07-2021, 09:15 PM
Replies: 3
Views: 288
Posted By TDENXJ
Sway Bar Quick Disc. - XJ - RE1130

Rubicon Express (RE1130) Adjustable Sway Bar Disconnect

Originally purchased for and fits 1996 Jeep Cherokee (XJ)

For 2”-3.5” lift

I paid $115 + tax/shipping couple months ago

Asking $70...
Jeep Forums: XJ Cherokee Technical Forum   07-01-2021, 08:29 PM
Replies: 17
Views: 1,537
Posted By TDENXJ
Glad to hear some grinding is normal. I got...

Glad to hear some grinding is normal.

I got up to higher speeds today and it seems like all the driveline vibrations are gone though I can still see rear axle needs rotated a few degrees to align....
Jeep Forums: XJ Cherokee Technical Forum   06-30-2021, 11:41 PM
Replies: 17
Views: 1,537
Posted By TDENXJ
CJ7-TIM, Thank you very much for your...

CJ7-TIM,

Thank you very much for your support.

Well, I got everything back together and installed tonight. I went for a mild test drive around block... so far it runs fine, shifts just okay......
Jeep Forums: XJ Cherokee Technical Forum   06-27-2021, 11:34 PM
Replies: 17
Views: 1,537
Posted By TDENXJ
Must have been the vent cap. With a better cap in...

Must have been the vent cap. With a better cap in place I could not duplicate the leak. So, it is finally bolted it up to the Jeep. Not the easiest job to do on your back using a floor jack (Built...
Jeep Forums: XJ Cherokee Technical Forum   06-27-2021, 05:20 PM
Replies: 17
Views: 1,537
Posted By TDENXJ
Maybe false alarm... investigating faulty vent...

Maybe false alarm... investigating faulty vent cap.
Jeep Forums: XJ Cherokee Technical Forum   06-27-2021, 04:57 PM
Replies: 17
Views: 1,537
Posted By TDENXJ
Mechanical Engineering. Though, I may have...

Mechanical Engineering.

Though, I may have celebrated too soon. I put 32oz of ATF in to see how it holds fluid and it was looking good until I rotated the TC on its side (Input gear shaft facing...
Jeep Forums: XJ Cherokee Technical Forum   06-26-2021, 11:48 PM
Replies: 17
Views: 1,537
Posted By TDENXJ
Praise God. It’s fixed. In preparation for...

Praise God. It’s fixed.

In preparation for the next round of mock ups and testing I cleaned the RTV off every surface ...again. I really hate that part... though I’m getting good at it lately.
...
Jeep Forums: XJ Cherokee Technical Forum   06-26-2021, 01:52 PM
Replies: 17
Views: 1,537
Posted By TDENXJ
All good points... I do also have a grade A used...

All good points... I do also have a grade A used factory range fork I could use (casting 16976).

I did rotate the shaft while trying to cycle through gears. It will go between a couple gears but...
Jeep Forums: XJ Cherokee Technical Forum   06-26-2021, 12:02 PM
Replies: 17
Views: 1,537
Posted By TDENXJ
Yes, I purchased the Omix-ada for the range...

Yes, I purchased the Omix-ada for the range fork17833 casting... it seemed to have good reviews for this particular part. Is there a better source?
Jeep Forums: XJ Cherokee Technical Forum   06-26-2021, 12:00 AM
Replies: 17
Views: 1,537
Posted By TDENXJ
This post is more like a journal at this point...

This post is more like a journal at this point (Lengthy I know... nobody will read)... I set out to get advise from others but now I hope my posts are helpful to someone else with similar problems....
Jeep Forums: XJ Cherokee Technical Forum   06-23-2021, 09:41 PM
Replies: 17
Views: 1,537
Posted By TDENXJ
Thank you for the response. I did not measure the...

Thank you for the response. I did not measure the rod length, however I did compare depth of the blind hole for rod on original output housing with that of the AA output housing and they are the...
Jeep Forums: XJ Cherokee Technical Forum   06-23-2021, 07:40 AM
Replies: 17
Views: 1,537
Posted By TDENXJ
Ok. My procedure for bench testing sounds...

Ok. My procedure for bench testing sounds acceptable. I still have the same “no shift” issue. I must have done something wrong internally during rebuild and SYE modifications. Based on shifting issue...
Jeep Forums: XJ Cherokee Technical Forum   06-22-2021, 11:38 PM
Replies: 17
Views: 1,537
Posted By TDENXJ
Proper Bench Test Procedure - NP231

Assuming a transfer case rebuild or SYE modification is done correctly what is required to perform a proper bench test or what is the best known method? i.e. is it necessary to fill fluids? Is it...
Jeep Forums: Engines & Drivetrain   06-21-2021, 12:01 AM
Replies: 5
Views: 1,173
Posted By TDENXJ
After talking to tech support from various...

After talking to tech support from various sources like Novak I decided to move forward with the 17833 range fork and the used range hub. Rebuild and reassembly with AA SYE went well until the final...
Jeep Forums: XJ Cherokee Technical Forum   06-17-2021, 07:11 AM
Replies: 3
Views: 2,433
Posted By TDENXJ
Understand this is really really old post but...

Understand this is really really old post but looking for same answers. Anyone?
Jeep Forums: Engines & Drivetrain   06-11-2021, 09:03 AM
Replies: 5
Views: 1,173
Posted By TDENXJ
Thank you for your input JeeperDon.

Thank you for your input JeeperDon.
Jeep Forums: Engines & Drivetrain   06-10-2021, 07:46 AM
Replies: 5
Views: 1,173
Posted By TDENXJ
Did I post this incorrectly?

Did I post this incorrectly?
Jeep Forums: Engines & Drivetrain   06-07-2021, 02:33 PM
Replies: 5
Views: 1,173
Posted By TDENXJ
Follow up to problem 4) I am comparing the...

Follow up to problem 4) I am comparing the original assembly with old seal to reassembly with new seal. Will a new seal add noticeable resistance on input gear shaft?
Showing results 1 to 20 of 22

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome