JeepForum.com - Search Results
Advanced Search
Showing results 1 to 20 of 250
Search took 0.04 seconds.
Search: Posts Made By: oldschool74cj5
Jeep Forums: Jeep CJ Forum   Yesterday, 02:25 PM
Replies: 24
Views: 388
Posted By oldschool74cj5
hello before pull the heads i would...

hello

before pull the heads i would also put air in the cylinder and see where it is leaking out, it would be one of three. intake or exhaust valve or possible going past the rings if they...
Jeep Forums: Jeep CJ Forum   07-01-2020, 08:27 PM
Replies: 24
Views: 388
Posted By oldschool74cj5
hello i read your original post again....

hello

i read your original post again. how long ago was the engine reworked? have you check the compression lately? the reason im asking is lapping valves doesnt work all that great. you...
Jeep Forums: Jeep CJ Forum   07-01-2020, 07:39 PM
Replies: 24
Views: 388
Posted By oldschool74cj5
hello have you checked to see if you have...

hello
have you checked to see if you have a bad intake vacuum leak? you need all three components to run. air, fuel and spark. sounds like you have run everything for the spark and some of the...
Jeep Forums: Jeep CJ Forum   06-30-2020, 07:59 PM
Replies: 11
Views: 314
Posted By oldschool74cj5
hello the only tool you really need...

hello

the only tool you really need is they tell you to make from a cotter pin. it is used to push one side of the seal that is in the block out of the groove it is in. then you slide the...
Jeep Forums: Jeep CJ Forum   06-30-2020, 07:18 PM
Replies: 7
Views: 212
Posted By oldschool74cj5
hello i have never trusted the tag on...

hello

i have never trusted the tag on a older jeep. people do some odd things. i was looking at one cj7 that had 4.11 in the rear but only around 3.53 still in the front. i found this by...
Jeep Forums: Jeep CJ Forum   06-30-2020, 07:08 PM
Replies: 4
Views: 151
Posted By oldschool74cj5
hello its been a quite few years since i...

hello
its been a quite few years since i have been in a dana 20. i had to look up the procedure. i was pretty sure that you have to turn the rod 90 degrees to remove the rod.

here is a link...
Jeep Forums: Jeep CJ Forum   06-30-2020, 06:19 PM
Replies: 3
Views: 128
Posted By oldschool74cj5
hello you normally dont need to...

hello

you normally dont need to replace the spring on the bar that goes across. i believe its more of a spring to keep the bar from rattling around between the shoe and the emergency brake...
Jeep Forums: Jeep CJ Forum   06-30-2020, 05:45 PM
Replies: 7
Views: 212
Posted By oldschool74cj5
hello a simple way that i figure out what...

hello
a simple way that i figure out what the ratio is without opening anything is. have the jeep on the ground tape a string to the rear drive shaft. push the vehicle forward where the tire...
Jeep Forums: Jeep CJ Forum   06-30-2020, 02:59 PM
Replies: 10
Views: 411
Posted By oldschool74cj5
hello the only thing i can think about is...

hello
the only thing i can think about is they were in that group of people who panic'd in the 80's and early 90's about the flipping a hi centered vehicle. there were people doing some strange...
Jeep Forums: Jeep CJ Forum   06-29-2020, 03:19 PM
Replies: 19
Views: 784
Posted By oldschool74cj5
hello i believe that is part of the reason...

hello
i believe that is part of the reason that warn stop making the full float kit. to me part of the problem is that there is nothing keeping the shaft from wanting to push outward. the...
Jeep Forums: Jeep CJ Forum   06-28-2020, 06:39 PM
Replies: 29
Views: 1,981
Posted By oldschool74cj5
hello mpg and jeep are 2 words that just...

hello

mpg and jeep are 2 words that just shouldnt go in a same sentence. thats like prius and cool. just 2 words that dont work. i would do a engine swap that performs the best for what you are...
Jeep Forums: Jeep CJ Forum   06-28-2020, 11:14 AM
Replies: 54
Views: 4,893
Posted By oldschool74cj5
hello before i was putting in a led light...

hello
before i was putting in a led light strip on the bottom of the dash for floor lighting i was thinking of wiring a ignition relay in and using the headlight switch to turn on the relay. i...
Jeep Forums: Jeep CJ Forum   06-28-2020, 11:05 AM
Replies: 22
Views: 925
Posted By oldschool74cj5
hello you have the stack up correct....

hello

you have the stack up correct. if it was me i would install studs into the aluminum plate. that is the way that almost all carbs were mounted onto a intake. i also think in my opinion...
Jeep Forums: Jeep CJ Forum   06-28-2020, 10:08 AM
Replies: 3
Views: 190
Posted By oldschool74cj5
hello the 258 is pretty much a low rpm...

hello

the 258 is pretty much a low rpm tractor motor. it is a undersquare engine meaning that the bore is smaller then the stroke. with that said that is what makes her such a torque motor...
Jeep Forums: Jeep CJ Forum   06-22-2020, 08:16 PM
Replies: 5
Views: 336
Posted By oldschool74cj5
hello you might have some air still in...

hello

you might have some air still in the lines. it doesnt take much to create a little bit of spongy feel. also have you adjusted the shoes on the drum brakes. you want to have them both...
Jeep Forums: Jeep CJ Forum   06-22-2020, 05:42 PM
Replies: 13
Views: 461
Posted By oldschool74cj5
hello its not all that uncommon now...

hello

its not all that uncommon now days to have the cam and lifters go bad. unless you are using a hot rod oil with the higher amount of dzzp in it. that doesn't mean you need a new long...
Jeep Forums: Jeep CJ Forum   06-18-2020, 04:14 PM
Replies: 11
Views: 380
Posted By oldschool74cj5
i agree 100 percent about the weber 38-dges from...

i agree 100 percent about the weber 38-dges from redline. that is what i have installed and was pretty easy to tune and run. mine has been on for about 3 years now. this year was the first trouble i...
Jeep Forums: Jeep CJ Forum   06-17-2020, 08:23 PM
Replies: 11
Views: 380
Posted By oldschool74cj5
hello whollsee i think is right about it...

hello
whollsee i think is right about it being a solex 34/34. i have run solex carbs years ago when i was into the bugs. they were good carbs when they were European made. unfor the Chinese...
Jeep Forums: Jeep CJ Forum   06-17-2020, 04:53 PM
Replies: 8
Views: 400
Posted By oldschool74cj5
hello im sure you wont have a problem...

hello

im sure you wont have a problem finding someone that lives in a hellmisisionsfornia that would need some of those parts if they are still working.

oldschool

that is the bad part about...
Jeep Forums: Jeep CJ Forum   06-15-2020, 08:53 PM
Replies: 20
Views: 890
Posted By oldschool74cj5
hello i can tell you a trick i use alot...

hello
i can tell you a trick i use alot for tapping a hole straight. when free handing the tapping you have the possibility of tapping at a angle. what i have is some small block that have a...
Showing results 1 to 20 of 250

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome