JeepForum.com - Search Results
Advanced Search
Showing results 1 to 20 of 50
Search took 0.06 seconds.
Search: Posts Made By: ECGS
Jeep Forums: TJ Wrangler Technical Forum   01-17-2018, 01:06 PM
Replies: 61
Views: 9,049
Posted By ECGS
1. I was notified of this thread this morning,...

1. I was notified of this thread this morning, otherwise we had no knowledge of anything except we took return of the axles and paid the freight both ways. This is why we did not respond.

2. The...
Jeep Forums: TJ Wrangler Technical Forum   02-05-2015, 09:12 AM
Replies: 20
Views: 2,565
Posted By ECGS
This axle is also not a cut down JK axle it is a...

This axle is also not a cut down JK axle it is a brand new axle built to our specs using a JK center section.

The tubes used have a thicker wall then JK standard Tubes. And the OD is 3.125 over...
Jeep Forums: TJ Wrangler Technical Forum   04-08-2014, 06:52 AM
Replies: 48
Views: 4,703
Posted By ECGS
You have to trim down the shortside .25 inches to...

You have to trim down the shortside .25 inches to get it off the crosspin. It was discussed in this thread at length. There are varying opinions on the subject so it is still a bit confusing. The...
Jeep Forums: Grand Cherokee General Discussion   01-13-2012, 09:46 PM
Replies: 688
Views: 63,924
Posted By ECGS
Woa good job dude 3 days to make 2 roll! ...

Woa good job dude 3 days to make 2 roll!


And no a WJ front does not fit in an XJ I want details and pics of that little dandy!
Jeep Forums: TJ Wrangler Technical Forum   12-27-2011, 04:41 PM
Replies: 21
Views: 2,515
Posted By ECGS
I would grind the Ball down and 1/8 inch on each...

I would grind the Ball down and 1/8 inch on each side. I don't know why currie sells a trac bar that does not fit the stock width bracket.
Jeep Forums: WJ Grand Cherokee Forum   11-04-2011, 10:27 AM
Replies: 21
Views: 1,661
Posted By ECGS
yes we have a nice bracket kit with truss ect....

yes we have a nice bracket kit with truss ect. housing end 35 spline shafts, Pretty much evrything you need.
Jeep Forums: WJ Grand Cherokee Forum   11-03-2011, 08:36 PM
Replies: 21
Views: 1,661
Posted By ECGS
We designed the housings end to take Wj brakes...

We designed the housings end to take Wj brakes abs compatible, Upgrade your 3rd to 35 spline and i have the shafts for you also.

If you want to do it i can give you some insight on how to build...
Jeep Forums: WJ Grand Cherokee Forum   08-18-2011, 09:19 AM
Replies: 21
Views: 6,115
Posted By ECGS
the WJ front is going to be getting installed in...

the WJ front is going to be getting installed in our shop jeep shortly after a testing period we will release with price. Since we will have already done the install, we will provide steering, brake...
Jeep Forums: WJ Grand Cherokee Forum   08-16-2011, 08:45 AM
Replies: 21
Views: 6,115
Posted By ECGS
Maybe you can the rear bolt in 60 is already...

Maybe you can the rear bolt in 60 is already available. http://eastcoastgearsupply.com/i-6164744-dana-60-bolt-in-wj-axel-assembly.html

And the front is so close, the TJ front 60 is waiting on coil...
Jeep Forums: TJ Wrangler Technical Forum   06-23-2011, 02:07 PM
Replies: 103
Views: 13,230
Posted By ECGS
By checking the angles on the new axle We felt it...

By checking the angles on the new axle We felt it was acceptable but we have used housings that are straighter. We will need to get the old axle back and go through the checks on it to see how far of...
Jeep Forums: TJ Wrangler Technical Forum   06-23-2011, 02:00 PM
Replies: 103
Views: 13,230
Posted By ECGS
So new or used: longside alignment method does...

So new or used: longside alignment method does not seem to be very telling. The disconcerting part is the tube check. Had this new housing been a used housing we would have likely not used it do to...
Jeep Forums: TJ Wrangler Technical Forum   06-23-2011, 01:55 PM
Replies: 103
Views: 13,230
Posted By ECGS
We would say shortside is definetly acceptable...

We would say shortside is definetly acceptable Now for the longside
Jeep Forums: TJ Wrangler Technical Forum   06-23-2011, 01:53 PM
Replies: 103
Views: 13,230
Posted By ECGS
The shortside shown is very close and the the...

The shortside shown is very close and the the puck would go in if forced. but is not completely true.
Jeep Forums: TJ Wrangler Technical Forum   06-23-2011, 01:51 PM
Replies: 103
Views: 13,230
Posted By ECGS
HERE IS AN UPDATE ON THE CAMBER ISSUE: We...

HERE IS AN UPDATE ON THE CAMBER ISSUE:

We built a jig for the front 30's to determine if a front axle is bent.......... Well from what we have found all of them our bent. We already knew this of...
Jeep Forums: TJ Wrangler Technical Forum   06-14-2011, 05:54 PM
Replies: 103
Views: 13,230
Posted By ECGS
Other issue from above. Customer wanted clayton...

Other issue from above. Customer wanted clayton brackets installed. Not a problem, we have the pieces in stock, we spoke on the phone multiple times with father and son on separate occasions. Order...
Jeep Forums: TJ Wrangler Technical Forum   06-14-2011, 05:04 PM
Replies: 103
Views: 13,230
Posted By ECGS
Our official response to the Dana 30 Camber...

Our official response to the Dana 30 Camber issue. We screwed up and sent a bent axle. Customer phoned us, and said, “there is an issue with camber.” I said “okay”, we discussed some other things, he...
Jeep Forums: TJ Wrangler Technical Forum   03-02-2011, 06:52 PM
Replies: 177
Views: 61,703
Posted By ECGS
LUCAS 85w140 Dino oil is all we use in every...

LUCAS 85w140 Dino oil is all we use in every differential. I believe synthetic has no place in differentials; regardless of what auto makers say. All I have is experience.

First, who cares? Save...
Jeep Forums: TJ Wrangler Technical Forum   01-20-2011, 07:36 AM
Replies: 27
Views: 1,973
Posted By ECGS
We will no longer be offering a Ford 9 junkyard...

We will no longer be offering a Ford 9 junkyard rear bracketed. Reason: They are weak and expensive. We can offer a fabricated housing 9" with nodular 3rd but of course the cost will be considerably...
Jeep Forums: Grand Cherokee General Discussion   12-22-2010, 08:28 AM
Replies: 49
Views: 4,378
Posted By ECGS
Is that your house in the background and your...

Is that your house in the background and your neighbors car behind it, or does it just look very similiar to your jeep. Rusty's has always been honorable to deal with. theres always a chance someone...
Jeep Forums: TJ Wrangler Technical Forum   11-29-2010, 07:37 PM
Replies: 48
Views: 4,703
Posted By ECGS
If you run a stock length shaft the shortside...

If you run a stock length shaft the shortside hits the crosspin, thats all there is to it. I dont care what ARB says. the crosspins are not in the same spot. But i give up the shaft did not fit so...
Showing results 1 to 20 of 50

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome