JeepForum.com - Search Results
Advanced Search
Showing results 1 to 20 of 250
Search took 0.05 seconds.
Search: Posts Made By: yellow85cj
Jeep Forums: Jeep CJ Forum   05-24-2019, 11:42 AM
Replies: 9
Views: 469
Posted By yellow85cj
Try the Repair Connector Store ...

Try the Repair Connector Store

https://www.repairconnector.com/products/Universal--License-Plate-and-Instrument-Panel-Socket-Single-Contact.html
...
Jeep Forums: Jeep CJ Forum   04-08-2019, 07:33 PM
Replies: 4
Views: 283
Posted By yellow85cj
One V in the balancer, second or third are bolt...

One V in the balancer, second or third are bolt on.
Don't forget to change your water pump to the V belt style. The serp belt runs in reverse of the V belt style.

Alt bracket is different.
...
Jeep Forums: Jeep CJ Forum   03-06-2019, 04:50 PM
Replies: 8
Views: 309
Posted By yellow85cj
I'm using an XJ column and just used the CJ...

I'm using an XJ column and just used the CJ dimmer switch plug in the XJ column connector. Works fine. Don't have the flash brights feature, but didn't want to have to do any other wiring.

Also...
Jeep Forums: Jeep CJ Forum   03-04-2019, 09:23 PM
Replies: 8
Views: 579
Posted By yellow85cj
A lot of work on that CJ10. At least they gave it...

A lot of work on that CJ10. At least they gave it sort of round headlights.
Jeep Forums: Jeep CJ Forum   09-24-2018, 06:08 PM
Replies: 10
Views: 569
Posted By yellow85cj
On your original question, I don't think that the...

On your original question, I don't think that the bearing is replaceable. Might check on the XJ forum (if in fact it is an XJ column) to see if it is replaceable.

Take the bell coupler with you...
Jeep Forums: Jeep CJ Forum   09-24-2018, 02:55 PM
Replies: 10
Views: 569
Posted By yellow85cj
Double D, think of a circle with 2 flat sides....

Double D, think of a circle with 2 flat sides. Yes it is the end of the column that firs into the universal joint of the intermediate shaft. (the intermediate shaft is what connects the column to the...
Jeep Forums: Jeep CJ Forum   09-24-2018, 02:22 PM
Replies: 10
Views: 569
Posted By yellow85cj
It's not a stock CJ column. It has a double D...

It's not a stock CJ column. It has a double D end, stock are splined ends.

I use an XJ column in my CJ as it was the easiest tilt column to find. Just have to cut the "bell" end, the part that...
Jeep Forums: Jeep CJ Forum   09-14-2018, 08:52 PM
Replies: 5
Views: 381
Posted By yellow85cj
The 4 and 6 are the same bracket. Only In A...

The 4 and 6 are the same bracket.
Only In A Jeep CJ shows a pretty good list.
Jeep Forums: Jeep CJ Forum   09-14-2018, 05:03 PM
Replies: 5
Views: 381
Posted By yellow85cj
Most AMC vehicles (not just Jeeps) non-serp belt...

Most AMC vehicles (not just Jeeps) non-serp belt engines used the same brackets.
Jeep Forums: Jeep CJ Forum   08-23-2018, 08:28 PM
Replies: 6
Views: 335
Posted By yellow85cj
You can make your own. Some square tube from the...

You can make your own. Some square tube from the local steel yard drop pile. It was a little wide but didn't make a difference. Cutoff wheel and drill. It's how I made mine for the tub swap.
Jeep Forums: Jeep CJ Forum   05-24-2018, 07:00 PM
Replies: 24
Views: 3,451
Posted By yellow85cj
Pretty sure the tabs on the distributor plug are...

Pretty sure the tabs on the distributor plug are on the wrong sides.
Ask me how I know.:grin2:
But you just have to trim them off and it will fit fine. Mine fit very tight.
But if you are...
Jeep Forums: Jeep CJ Forum   04-15-2018, 08:52 AM
Replies: 5
Views: 305
Posted By yellow85cj
It's there to help vaporize fuel when the engine...

It's there to help vaporize fuel when the engine is cold, shuts off when engine temp reaches 150* or so IIRC. Gas vaporizes at 140*.
Since the intake is water cooled/heated, wouldn't think it...
Jeep Forums: Jeep CJ Forum   04-05-2018, 08:32 AM
Replies: 24
Views: 1,676
Posted By yellow85cj
From the parts manual.

From the parts manual.
Jeep Forums: Jeep CJ Forum   04-04-2018, 09:36 PM
Replies: 24
Views: 1,676
Posted By yellow85cj
I made some frame brackets using 1/4" angle with...

I made some frame brackets using 1/4" angle with gussets. One on each side of the frame on each side. My homemade bumper is bolted through to the frame brackets.

When I was down to the frame, I...
Jeep Forums: Jeep CJ Forum   02-20-2018, 06:26 PM
Replies: 14
Views: 591
Posted By yellow85cj
May be a bit more than you want to do. YJ 4.0 and...

May be a bit more than you want to do. YJ 4.0 and XJ pump should be the same for mounting. You'll have to go full serp belt. The link was done on a California (serp belt) 4.2.
...
Jeep Forums: Jeep CJ Forum   01-28-2018, 09:24 AM
Replies: 11
Views: 564
Posted By yellow85cj
While it would be easy to do so (MSD wants the...

While it would be easy to do so (MSD wants the green to go to the violet wire and the violet wire to go to the orange wire) , I used their harness connector so I didn't do any splicing. Plug 'n play....
Jeep Forums: Jeep CJ Forum   01-27-2018, 01:49 PM
Replies: 13
Views: 921
Posted By yellow85cj
Problem...

Problem solved.:pickle::bacon::pickle::bacon::pickle::bacon:

Well after trying everything I could think of and trying everything others thought from carb adjustments, to vacuum canister...
Jeep Forums: Jeep CJ Forum   01-27-2018, 01:41 PM
Replies: 11
Views: 564
Posted By yellow85cj
Problem...

Problem solved.:bacon::pickle::bacon::pickle::bacon:

Well after trying everything I could think of and trying everything others thought from carb adjustments, to vacuum canister adjustments to...
Jeep Forums: Jeep CJ Forum   01-19-2018, 09:36 AM
Replies: 11
Views: 564
Posted By yellow85cj
Fresh rebuilt 258 4.0 head Ford large cap...

Fresh rebuilt 258
4.0 head
Ford large cap and rotor (brass contacts)
New dist (and same happens with used dist) Pre 83 weights
Pre 83 new Carter BBD
MSD 6201 ignition
MSD TFI coil
8 mm plug...
Jeep Forums: Jeep CJ Forum   01-18-2018, 08:01 PM
Replies: 11
Views: 564
Posted By yellow85cj
Because I can't seem to get the 258 to run...

Because I can't seem to get the 258 to run properly. So thought maybe I didn't understand how the advance works. Now know that the centrifugal advance is why the rotor can turn just a bit. Maybe a...
Showing results 1 to 20 of 250

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome