JeepForum.com - Search Results
Advanced Search
Showing results 1 to 20 of 250
Search took 0.05 seconds.
Search: Posts Made By: zjosh93
Jeep Forums: ZJ Grand Cherokee Forum   Yesterday, 07:40 AM
Replies: 5
Views: 167
Posted By zjosh93
If you live near a decent plastic supply shop you...

If you live near a decent plastic supply shop you can get big sheets of ABS plastic and try to do it that way. ABS plastic is thermoset so you can shape and mold it using a heat gun. It also responds...
Jeep Forums: ZJ Grand Cherokee Forum   Yesterday, 07:28 AM
Replies: 2
Views: 109
Posted By zjosh93
I wouldn't hesitate to use Fel-Pro seals. I've...

I wouldn't hesitate to use Fel-Pro seals. I've used them on several engines and haven't had any problems. My impression is that this is one area that the aftermarket improves on factory parts.

I...
Jeep Forums: ZJ Grand Cherokee Forum   03-19-2020, 07:32 AM
Replies: 12
Views: 380
Posted By zjosh93
Yeah, I first replaced mine with Anchor mounts....

Yeah, I first replaced mine with Anchor mounts. The driver's side mount failed every 8-12 months. After 2 or 3 I put the Energy Suspensions mount in and it lasted about 5 years.
Jeep Forums: ZJ Grand Cherokee Forum   03-18-2020, 07:26 PM
Replies: 14
Views: 344
Posted By zjosh93
Not disagreeing, the tag on the LSD should ID it....

Not disagreeing, the tag on the LSD should ID it. But, IMS, there was originally a tag on all the rear diff covers. A lot of people just toss them when they change the fluid so it's not uncommon to...
Jeep Forums: ZJ Grand Cherokee Forum   03-18-2020, 08:04 AM
Replies: 12
Views: 380
Posted By zjosh93
I'm going to try replacing the insert with a...

I'm going to try replacing the insert with a 2793R. If you look at pictures of the left side mount most people sell it has just two rubber "legs" holding up the cross bar. The 2793R version has extra...
Jeep Forums: ZJ Grand Cherokee Forum   03-17-2020, 07:35 AM
Replies: 12
Views: 380
Posted By zjosh93
The round energy suspensions mount inserts listed...

The round energy suspensions mount inserts listed for the V8 will fit the 4.0 mount shells. I put them in my 93 4.0. When I put them on both sides I got a vibration I didn't like. I left the drivers...
Jeep Forums: ZJ Grand Cherokee Forum   03-17-2020, 07:27 AM
Replies: 28
Views: 1,351
Posted By zjosh93
There are several wheel cleaners that contain...

There are several wheel cleaners that contain hydrofluoric acid. Typically the ones labeled as etching, cast aluminum, or mag wheel cleaner.
Jeep Forums: ZJ Grand Cherokee Forum   03-16-2020, 03:55 PM
Replies: 28
Views: 1,351
Posted By zjosh93
What wheel cleaner? If you got one of the acidic...

What wheel cleaner? If you got one of the acidic versions you probably etched the glass. Only solution is to polish the etch out. Get some cerium oxide powder and a felt polishing pad. It's cheap and...
Jeep Forums: ZJ Grand Cherokee Forum   03-09-2020, 09:09 AM
Replies: 2
Views: 229
Posted By zjosh93
Those are the hoses for the 5.2. If you have a...

Those are the hoses for the 5.2. If you have a 4.0 they won't work. The rubber hose on the end won't reach the radiator fittings since the 4.0 fittings are on the other side. Unfortunately, if you...
Jeep Forums: ZJ Grand Cherokee Forum   03-06-2020, 01:00 PM
Replies: 8
Views: 347
Posted By zjosh93
I always recommend giving the cam companies a...

I always recommend giving the cam companies a call. Their tech guys are usually pretty good and can help steer you to the right cam. They can help you cut through to the reality of your build, your...
Jeep Forums: ZJ Grand Cherokee Forum   03-04-2020, 08:14 AM
Replies: 7
Views: 274
Posted By zjosh93
Will he have to drill out the mount or the link...

Will he have to drill out the mount or the link for a 1/2" bolt? The original is a M12 and a tight fit in the mount as 1996maroonzjf said. 12 mm is a bit smaller than 1/2".
Jeep Forums: ZJ Grand Cherokee Forum   03-03-2020, 08:27 AM
Replies: 5
Views: 134
Posted By zjosh93
If it turns without the key I'd replace the...

If it turns without the key I'd replace the cylinder. Pull the cylinder though and take a look at the end. A common failure is for the ring at the end of the cylinder to break. That could be causing...
Jeep Forums: ZJ Grand Cherokee Forum   03-03-2020, 07:05 AM
Replies: 7
Views: 289
Posted By zjosh93
I was wondering how you were handling the...

I was wondering how you were handling the bellhousing. IMS the V8 ZJ setup is unique in that the starter is on the passenger side. So you either have to cut up and weld the bellhousing or redo the...
Jeep Forums: ZJ Grand Cherokee Forum   03-02-2020, 09:45 PM
Replies: 16
Views: 345
Posted By zjosh93
The damper that was on it when I bought it in 07...

The damper that was on it when I bought it in 07 was not OEM. It looked like a Dorman. That one failed in 08 or so. I installed a brand new Dorman part because I was still working at a parts store...
Jeep Forums: ZJ Grand Cherokee Forum   03-02-2020, 07:06 PM
Replies: 7
Views: 274
Posted By zjosh93
Looks like you broke the lower anti-sway bar...

Looks like you broke the lower anti-sway bar bolt, Mopar part number 6502930. Discontinued, but there's a NOS one on eBay right now. M12x1.75x70. Truss head. You could probably use a generic bolt but...
Jeep Forums: ZJ Grand Cherokee Forum   03-02-2020, 06:58 PM
Replies: 3
Views: 183
Posted By zjosh93
For the price I just swap in a new one. Every...

For the price I just swap in a new one. Every time my gauge started acting up it was the sensor, and twice it was a precursor to the gauge leaking, including one time that it started spraying down my...
Jeep Forums: ZJ Grand Cherokee Forum   03-02-2020, 12:34 PM
Replies: 16
Views: 345
Posted By zjosh93
That's a reasonable way of doing it. I just rent...

That's a reasonable way of doing it. I just rent the tool. You need to have something to get it started at least, the stock bolt is too short.

IMS it's the old small block chevy that had real...
Jeep Forums: ZJ Grand Cherokee Forum   03-02-2020, 09:23 AM
Replies: 16
Views: 345
Posted By zjosh93
FWIW, if you have a long enough breaker bar you...

FWIW, if you have a long enough breaker bar you can put the bar on the crank bolt and wedged up against the frame, then you hit the starter for a second and it'll break it free. Just have to be very...
Jeep Forums: ZJ Grand Cherokee Forum   03-02-2020, 09:07 AM
Replies: 16
Views: 345
Posted By zjosh93
The first time I changed the harmonic damper on...

The first time I changed the harmonic damper on my 93 I had to move the radiator to fit the puller. The last couple times I didn't. IMS the first time I used the puller with bolts that thread into...
Jeep Forums: ZJ Grand Cherokee Forum   02-27-2020, 07:42 AM
Replies: 8
Views: 261
Posted By zjosh93
Actually, I that's the 2WD...

Actually, I that's the 2WD driveshaft/outputshaft/extension housing seal. That's why I was saying that you can't really trust the 2WD/4WD notes. If you look at the notes for the National seal with...
Showing results 1 to 20 of 250

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome