JeepForum.com - Search Results
Advanced Search
Showing results 1 to 20 of 250
Search took 0.05 seconds.
Search: Posts Made By: rjbruzan
Jeep Forums: Engines & Drivetrain   07-22-2021, 07:40 PM
Replies: 9
Views: 901
Posted By rjbruzan
Ratech has the correct thick shims. Newer D30s...

Ratech has the correct thick shims. Newer D30s use this type of shim

Ron
Jeep Forums: Engines & Drivetrain   07-17-2021, 09:39 AM
Replies: 5
Views: 607
Posted By rjbruzan
Sounds like you are very close. Keep at it. I...

Sounds like you are very close. Keep at it. I can’t get at alldata until Wednesday to print out the wiring diagrams. The shifting would be correct if the TCM is not working correctly. 1-2 is done...
Jeep Forums: XJ Cherokee Technical Forum   07-16-2021, 08:49 PM
Replies: 9
Views: 1,110
Posted By rjbruzan
My aged 98 XJ with 3” Old Man Emu and Bilstein...

My aged 98 XJ with 3” Old Man Emu and Bilstein shocks rides smooth. This is with 265/75-15s at 25 psi. It would not surprise me that you could run your 235s at 27 psi with excellent results. The door...
Jeep Forums: XJ Cherokee Technical Forum   07-16-2021, 08:40 PM
Replies: 17
Views: 1,883
Posted By rjbruzan
The smoking while going over the mountains is...

The smoking while going over the mountains is most likely the trans blowing vapor out the vent tube. Was the back hatch oily? Do you have oversized tires or a heavy load?
Where is the exhaust...
Jeep Forums: Audio, CB & Ham Radios, GPS, & Electrical   07-16-2021, 08:35 PM
Replies: 3
Views: 666
Posted By rjbruzan
Those voltages are good. Ron

Those voltages are good.

Ron
Jeep Forums: Engines & Drivetrain   07-16-2021, 08:29 PM
Replies: 5
Views: 607
Posted By rjbruzan
What year diagram/TCM are you using? My 93 XJ...

What year diagram/TCM are you using? My 93 XJ didn’t have that switch. Perhaps its a pre 91 (Renix ?). The TCM are plug and play. Try adding power to the switch or a wiring diagram to match you PCM....
Jeep Forums: Engines & Drivetrain   07-16-2021, 08:17 PM
Replies: 2
Views: 823
Posted By rjbruzan
Go back to American Motors about 1965 and this...

Go back to American Motors about 1965 and this engine started as a 199 cubic in. Then up graded to 232 inches. Around 1970-71 the bell housing pattern changed to match the V8s. It was also used in...
Jeep Forums: Engines & Drivetrain   07-16-2021, 08:09 PM
Replies: 2
Views: 601
Posted By rjbruzan
Sounds like you don’t need the flush. Just my 2...

Sounds like you don’t need the flush. Just my 2 cents
Jeep Forums: Tires & Wheels   07-04-2021, 09:41 PM
Replies: 1
Views: 607
Posted By rjbruzan
Summit Racing has lots of options and is easy to...

Summit Racing has lots of options and is easy to use for information

Ron
Jeep Forums: Engines & Drivetrain   06-09-2021, 08:55 AM
Replies: 1
Views: 354
Posted By rjbruzan
Did you do the ignition basics? Plugs, wires,...

Did you do the ignition basics? Plugs, wires, points, dwell and timing?

Ron
Jeep Forums: Engines & Drivetrain   06-02-2021, 07:50 PM
Replies: 3
Views: 946
Posted By rjbruzan
If from the middle of the vehicle I’d check the...

If from the middle of the vehicle I’d check the drive shafts. U joints and cv joint at transfer case.

Ron
Jeep Forums: WJ Grand Cherokee Forum   06-01-2021, 10:07 AM
Replies: 9
Views: 818
Posted By rjbruzan
www.jeppaspjall.is/viewtopic.php?=9&t=35901 ...

www.jeppaspjall.is/viewtopic.php?=9&t=35901

Better link?

Ron
Jeep Forums: Engines & Drivetrain   05-26-2021, 08:48 PM
Replies: 2
Views: 627
Posted By rjbruzan
If you put your location under your user name you...

If you put your location under your user name you may get better results.

Ron
Jeep Forums: XJ Cherokee Technical Forum   05-24-2021, 07:02 PM
Replies: 12
Views: 2,049
Posted By rjbruzan
TSC is 100% correct Ron

TSC is 100% correct

Ron
Jeep Forums: General Jeep & Off-Road Equipment   05-23-2021, 04:01 PM
Replies: 8
Views: 1,086
Posted By rjbruzan
That looks like a 2” spacer Ron

That looks like a 2” spacer

Ron
Jeep Forums: XJ Cherokee Technical Forum   05-16-2021, 07:14 PM
Replies: 4
Views: 426
Posted By rjbruzan
Loose belt or the compresssor is froze up Ron

Loose belt or the compresssor is froze up

Ron
Jeep Forums: WJ Grand Cherokee Forum   05-15-2021, 08:52 PM
Replies: 11
Views: 685
Posted By rjbruzan
Perhaps it’s time to get a more powerful impact....

Perhaps it’s time to get a more powerful impact. A Milwaukee 2767 will do a nice job. About 250 for a bare tool. It is strong enough to crush a crush sleeve or remove and install axle nuts. You do...
Jeep Forums: WJ Grand Cherokee Forum   05-15-2021, 06:54 PM
Replies: 11
Views: 685
Posted By rjbruzan
Adding more torque to the pinion nut after the...

Adding more torque to the pinion nut after the bearings are seated can not move the pinion in any further. You are only tightening the bearing preload. You said o preload and all moved well now if...
Jeep Forums: XJ Cherokee Technical Forum   05-12-2021, 09:40 PM
Replies: 5
Views: 518
Posted By rjbruzan
The proper term is “welding project”. Weld the...

The proper term is “welding project”. Weld the divits in and grind to match the unworn area.
Not a fun job but is easier and cheaper than replacing the knuckle.

Ron
Jeep Forums: XJ Cherokee Technical Forum   05-07-2021, 06:10 PM
Replies: 12
Views: 2,049
Posted By rjbruzan
I’ve towed and still tow my XJ,WJ and TJ never...

I’ve towed and still tow my XJ,WJ and TJ never added a mile to the odometer.

Ron
Showing results 1 to 20 of 250

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome