JeepForum.com - Search Results
Advanced Search
Showing results 1 to 20 of 22
Search took 0.11 seconds.
Search: Posts Made By: kennuck
Jeep Forums: Jeep CJ Forum   06-12-2020, 05:06 PM
Replies: 13
Views: 821
Posted By kennuck
The kit is a pretty easy install. The front...

The kit is a pretty easy install. The front shackle hangers require you to drill one additional hole in the frame rail. I did not do a spring over just the shackle hangers and u bolt skids for the...
Jeep Forums: Jeep CJ Forum   06-11-2020, 08:13 PM
Replies: 13
Views: 821
Posted By kennuck
The stock front bumper fits no issues. The front...

The stock front bumper fits no issues. The front frame overlay does not fit without trimming around the shackle hanger. I never run the frame overlay, too bad I have thrown so many out over the...
Jeep Forums: Jeep CJ Forum   05-22-2020, 06:35 PM
Replies: 13
Views: 821
Posted By kennuck
Jim1611 this is not the first one I have done...

Jim1611 this is not the first one I have done with the rocky road kit, it drives fine with the kit installed. This one has 2.5 lift springs with 36" Super Swampers.

Keith I have a stock bumper...
Jeep Forums: Jeep CJ Forum   05-22-2020, 04:41 PM
Replies: 13
Views: 821
Posted By kennuck
I should have explained this in my original post....

I should have explained this in my original post. The front shackles are part of the YJ SUA kit from Rocky Road, it accommodates the wider 2.5" wide springs, and locates the front spring hanger about...
Jeep Forums: Jeep CJ Forum   05-22-2020, 03:49 PM
Replies: 13
Views: 821
Posted By kennuck
YJ Springs too much lift

I installed Omix Ada 18201.20 front and 18201.23 rear springs on my CJ7. These are supposed to be stock height but it seem more like a 4" lift to me. Did I get the right springs? FYI tires are 33"...
Jeep Forums: Jeep CJ Forum   05-22-2020, 03:19 PM
Replies: 5
Views: 426
Posted By kennuck
1999-2004 Chevy Silverado with 5.3 4l60e, rework...

1999-2004 Chevy Silverado with 5.3 4l60e, rework the harness using info at LT1swap.com to keep cost down, Tcase adapter to your Dana 300. Lots of power, reliable, and good fuel economy. LS for the...
Jeep Forums: Jeep CJ Forum   05-21-2020, 01:10 PM
Replies: 879
Views: 164,731
Posted By kennuck
Here is what the hood gap looks like with the...

Here is what the hood gap looks like with the hood lifted about 1.5"
Jeep Forums: Jeep CJ Forum   05-21-2020, 12:58 PM
Replies: 879
Views: 164,731
Posted By kennuck
O1dSoldier the radius is pretty close to the...

O1dSoldier the radius is pretty close to the radius of the hood, not like the drivers side of Keiths that isn't even close so maybe they addressed the radius. Its the gap between the hood and the...
Jeep Forums: Jeep CJ Forum   05-18-2020, 04:18 PM
Replies: 879
Views: 164,731
Posted By kennuck
The cowl area is the biggest hurdle, the rest is...

The cowl area is the biggest hurdle, the rest is just opening up or moving holes not as bad as it seems, its just frustrating. On a positve note it is good original thickness steel so its pretty...
Jeep Forums: Jeep CJ Forum   05-18-2020, 03:54 PM
Replies: 879
Views: 164,731
Posted By kennuck
And since everybody likes pics

And since everybody likes pics
Jeep Forums: Jeep CJ Forum   05-18-2020, 03:48 PM
Replies: 879
Views: 164,731
Posted By kennuck
Thanks Keith, yours turned out real nice, gives...

Thanks Keith, yours turned out real nice, gives me some hope for mine. How did you get the hood gap so good is assume you did some metal work in that area. Yep cowl vent 1/4" off centerline closer to...
Jeep Forums: Jeep CJ Forum   05-17-2020, 03:28 PM
Replies: 879
Views: 164,731
Posted By kennuck
Just worked on it a little more this aft. none of...

Just worked on it a little more this aft. none of the holes line up for the windshield or tailgate. What is the point of putting the holes in if you are not going to line them up!!! It would be...
Jeep Forums: Jeep CJ Forum   05-17-2020, 03:21 PM
Replies: 879
Views: 164,731
Posted By kennuck
I know this is an old thread but I'm hoping...

I know this is an old thread but I'm hoping people are still paying attention as information on MD Juan tubs is limited it seems.

I just picked mine up and it looks like most of the issues have...
Jeep Forums: Jeep CJ Forum   04-20-2020, 12:54 PM
Replies: 9
Views: 267
Posted By kennuck
Yep

Yep
Jeep Forums: Jeep CJ Forum   04-20-2020, 12:50 PM
Replies: 9
Views: 267
Posted By kennuck
Here is a pic

Here is a pic
Jeep Forums: Jeep CJ Forum   04-20-2020, 12:45 PM
Replies: 9
Views: 267
Posted By kennuck
The two holes on the Drivers side is for the...

The two holes on the Drivers side is for the swing out tire carrier latch.
Jeep Forums: Jeep CJ Forum   04-20-2020, 12:43 PM
Replies: 9
Views: 267
Posted By kennuck
The two pairs of holes near the tailgate are for...

The two pairs of holes near the tailgate are for the swing out tire carrier. The holes that are around the corner are for the spare tire stop so that it doesn't break the tail light when you swing...
Jeep Forums: Jeep CJ Forum   04-19-2020, 07:45 PM
Replies: 24
Views: 1,293
Posted By kennuck
Finished Jeep

Finished Jeep
Jeep Forums: Jeep CJ Forum   04-19-2020, 07:32 PM
Replies: 24
Views: 1,293
Posted By kennuck
2x5 tube, I used 10" Channel Iron for the front...

2x5 tube, I used 10" Channel Iron for the front cross member and 3x3 angle for the cross member the front of the tank mounts to.
Jeep Forums: Jeep CJ Forum   04-19-2020, 04:45 PM
Replies: 24
Views: 1,293
Posted By kennuck
I made a couple of frames. Not all that hard.

I made a couple of frames. Not all that hard.
Showing results 1 to 20 of 22

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome