JeepForum.com - Search Results
Advanced Search
Showing results 1 to 20 of 250
Search took 0.03 seconds.
Search: Posts Made By: wblackm
Jeep Forums: Jeep CJ Forum   04-16-2019, 08:28 AM
Replies: 18
Views: 2,509
Posted By wblackm
A little bit of an old thread here, my CJ does...

A little bit of an old thread here, my CJ does not have a slider on the driver side and is bolted to the riser. I am trying to determine how much these sliders will allow the seat to move back.
...
Jeep Forums: Jeep CJ Forum   02-20-2015, 06:44 AM
Replies: 10
Views: 616
Posted By wblackm
On another note, if someone has adapted a t18 to...

On another note, if someone has adapted a t18 to a dana 300, the length of that portion of the drive line will be different. Different enough to cause problems with driveline angles etc.? That is...
Jeep Forums: Jeep CJ Forum   01-28-2015, 09:05 AM
Replies: 76
Views: 9,278
Posted By wblackm
Check your steering shaft as well. I replaced my...

Check your steering shaft as well. I replaced my entire system, except for that. It helped, but it turns out a lot of the play was in the coupling between the shaft and the box itself. Granted I...
Jeep Forums: Jeep CJ Forum   08-15-2014, 08:27 AM
Replies: 46
Views: 6,045
Posted By wblackm
I will contradict one statement from earlier. ...

I will contradict one statement from earlier. You do need to be selective with your transmission fluid. As was also stated before, you need use either GL-4 rated gear lube only(Not GL-5 which is...
Jeep Forums: Jeep CJ Forum   07-17-2014, 07:42 AM
Replies: 15
Views: 1,212
Posted By wblackm
I would run stock springs soa(Maybe a 1 inch BL...

I would run stock springs soa(Maybe a 1 inch BL too), and get some tube fenders, and do some trimming in the rear. Keep that center of gravity lower. You get into stretching and that's big bucks. ...
Jeep Forums: Jeep CJ Forum   05-14-2014, 02:36 PM
Replies: 33
Views: 2,483
Posted By wblackm
To properly install a double cardan DS, the...

To properly install a double cardan DS, the pinion should be rotated to point directly at the output shaft of the Tcase.

This will most likely involve cutting and re-welding spring perches.
...
Jeep Forums: Jeep CJ Forum   05-13-2014, 02:40 PM
Replies: 56
Views: 5,081
Posted By wblackm
Don't skip out on the Grand Teton's when you are...

Don't skip out on the Grand Teton's when you are that close. I actually prefer them over Yellowstone, less touristy. FYI that pic with the tent is the Teton's. Looks like an AWESOME spot!
Jeep Forums: Jeep CJ Forum   05-12-2014, 02:56 PM
Replies: 1
Views: 496
Posted By wblackm
The auto store should have rolls in the back they...

The auto store should have rolls in the back they can cut any length. I don't remember what size mine is. The OD is somewhere between 1/2" and 3/4".

I just got 5 ft, and cut it to length when I...
Jeep Forums: South Carolina Jeep Forum   05-12-2014, 10:51 AM
Replies: 6
Views: 1,560
Posted By wblackm
I am going to have fishers work on a custom trac...

I am going to have fishers work on a custom trac arm for my CJ. If I remember I will let you know how it goes(this will be a little while down the road--so don't look for it too soon.)
Jeep Forums: South Carolina Jeep Forum   05-06-2014, 08:07 AM
Replies: 2
Views: 1,092
Posted By wblackm
I need a custom trac arm, Greenville Fabricators?

I need a custom track arm to limit axle wrap on my SOA CJ7.

I had used foothills 4x4 in the past, but went by and they appear to be closed.

Anyone have any experience with anyone else in the...
Jeep Forums: South Carolina Jeep Forum   05-06-2014, 08:02 AM
Replies: 6
Views: 1,560
Posted By wblackm
I have used Fishers garage on Congaree for all my...

I have used Fishers garage on Congaree for all my vehicles for years. I typically have the really 4x4 specific stuff done elsewhere, but I have had gears and axles set up there, etc.

They have...
Jeep Forums: Jeep CJ Forum   04-30-2014, 06:49 AM
Replies: 10
Views: 911
Posted By wblackm
Mine would not leak except under a large heat...

Mine would not leak except under a large heat load, sometimes at low speeds, but primarily after shutoff(after a time of low speed) when the heat load and pressure are the highest.

One thing is...
Jeep Forums: Jeep CJ Forum   04-25-2014, 06:34 AM
Replies: 47
Views: 5,907
Posted By wblackm
Here is a picture: 1291057

Here is a picture:



1291057
Jeep Forums: Jeep CJ Forum   04-25-2014, 06:19 AM
Replies: 47
Views: 5,907
Posted By wblackm
GL4/5 oil is not good for the brass synchros. ...

GL4/5 oil is not good for the brass synchros. Either go with a GL4 only, or run sythetic like has been mentioned. I run mobil 1 75w90 syth. gear lube in mine for the last 2 years with no issues. I...
Jeep Forums: Jeep CJ Forum   04-21-2014, 12:37 PM
Replies: 11
Views: 1,769
Posted By wblackm
Be aware that the 3 core will be thicker. This...

Be aware that the 3 core will be thicker. This will change the clearance between the face of the radiator and the pulleys. I would recommend buying the radiator you want, installing, and then...
Jeep Forums: Jeep CJ Forum   04-21-2014, 12:19 PM
Replies: 24
Views: 1,325
Posted By wblackm
Open diffs are MUCH preferred in snow. Living in...

Open diffs are MUCH preferred in snow. Living in NJ this should play large role in your decision unless you never use the jeep in snow.
Jeep Forums: Jeep CJ Forum   04-17-2014, 08:28 AM
Replies: 27
Views: 1,150
Posted By wblackm
Gclyne is partly right, but only if referring to...

Gclyne is partly right, but only if referring to conventional oil.

However, you don't have to use GL4. A synthettic gear oil(Royal Purple, Mobil 1, Amsoil, or Pennzoil syncromesh will work...
Jeep Forums: Jeep CJ Forum   04-16-2014, 01:48 PM
Replies: 16
Views: 1,021
Posted By wblackm
It is all actually attached to the motor, but in...

It is all actually attached to the motor, but in stock form there are 2 separate holes in the fire wall. Connect them up and see if it works. If you cannot shut it off, you probably have a bad...
Jeep Forums: Jeep CJ Forum   04-13-2014, 03:12 PM
Replies: 14
Views: 623
Posted By wblackm
Thanks for all the help Matt and LG. I got some...

Thanks for all the help Matt and LG. I got some grease and put it on the drive shafts and that seems to have at least temporarily stopped the issue.

I also greased me spring bushings, I do this...
Jeep Forums: Jeep CJ Forum   04-13-2014, 11:49 AM
Replies: 14
Views: 623
Posted By wblackm
Will do, do you have a grease you recommend? As...

Will do, do you have a grease you recommend? As the last stuff apparently didn't last as long as I though it should?

I just used wheel bearing grease last time, maybe that was mistake, or maybe I...
Showing results 1 to 20 of 250

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome