|Topic Review (Newest First)|
|Today 12:50 AM|
Originally Posted by TheBoogieman View Post
Just a pipe thread fitting so....
Something like this in the appropriate size.
When researching it I did come across something where somebody said not to use a barbed fitting and instead use something like this:
But I can't remember why though.
|Yesterday 10:22 PM|
|TheBoogieman||Found the source of my antifreeze leak. Water pump inlet tube wasn't tightened down completely by the PO when he replaced the pump. Now I need to rig up a new tube that can be tightened without removing everything. I'm thinking a shorter straight tube and longer hose.|
|Yesterday 03:18 PM|
|SmashDN||Added some AC juice. Much needed. It has been 96* here the last two days with 104* heat index.|
|08-16-2019 05:36 PM|
Originally Posted by Kettles View Post
|08-16-2019 04:36 PM|
Just made my 2-door so much more fun in a parking lot...
|08-16-2019 09:16 AM|
Originally Posted by MaskedMallard View Post
If and when I get this figured out will post in more detail with pictures.
|08-16-2019 03:45 AM|
Did you weld in the brackets for the rear seat headrests? I got my brackets from a Grand Cherokee & had the brackets cut out from the back of the GC & welded into the XJ.
|08-15-2019 12:35 PM|
Taken the last couple days off but for a few days before that was feeling my way through my rear seat headrest install.
Have not figured out everything yet but am getting there.
|08-15-2019 10:02 AM|
Yesterday I dropped a new Efan in it that I got from a local salvage Jeep an swapped the older pin style wiper arms out for 97+ wiper arms and new wiper blades front and rear. This morning I adjusted the driver's door striker pin in just hair so the back of the door would seal. I've had some wind noise from that area for a while but it hasn't been very loud, one day I looked back and noticed light coming in from the lower part of the door seal (these are brand new door seals) so did a small adjustment. Seals great now and the door is flush with the one behind it again.
|08-14-2019 05:06 PM|
|TheBoogieman||Washed it for the first time in a month. I need to align it again in the morning when it's below 90 outside.|
|08-11-2019 09:26 PM|
Originally Posted by Jakegrovephoto View Post
In other news, I'm gonna be back stateside the month of September officially so the jeep will finally get to be driven and mods will be installed. I have everything just about ready for the rocktrak swap except drive shafts which I can't order until I get the measurements with it installed. The guy I purchased it from installed 1350 yikes on it so I'm thinking about just getting matching pinion yokes rather than running a conversion joint at both ends. Once I swap to tons down the road, all I will need to do is lengthen or shorten the shafts.
Sent from my LM-V405 using Tapatalk
|08-11-2019 02:44 PM|
Got hooked up with some seats from an ‘03 sequioa. The fold flat option sits at 17” high from the front cab floor. Should just mock up to fit under a bed platform system I’ll be building flush with the rear wheel wells.
Onto tear down and adapting a narrower set of tracks to fit the trans tunnel.
|08-08-2019 11:22 AM|
So I figured I let the bedlined tail light guards cure long enough.
Put them back on.
Awhile back Kmart, I think, was blowing this out at something like $2 a can. So I figured I would
grab it and maybe it will come in handy for something.
So I decided to try it on this small leak I have developed. I thought I might have gotten it the first time but noooo.
The first time I used that 3M RTV that comes in the strips in the box. Decided to try the Rustoleum out.
Using my air hose I think I figured out where the small section I missed is. Right around the plate under that bolt.
|08-08-2019 04:40 AM|
Originally Posted by shooptube View Post
|08-07-2019 10:49 AM|
|75SV1||bought fenders, hood and cowl in the correct color. Also, the wood grain center dash piece. Should have bought the door skins too. Looking for a Sienna Red header panel. I have a few possibilities from searching on Car-Parts.com. See if one of them will ship.|
|This thread has more than 15 replies. Click here to review the whole thread.|