JeepForum.com - Reply to Topic
Thread: 93 jeep grand cherokee(4.0) radiator needs to be replaced Reply to Thread
Title:
Message:

Register Now



In order to be able to post messages on the JeepForum.com forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid e-mail address for yourself.



Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
06-18-2015 12:41 PM
merlot2twisty Getting the lower hose boss past the steering gearbox can be a challenge, but if you work patiently and angle and pull, you can get it past there.
06-17-2015 10:26 PM
mikem350 Don't forget to check the fan clutch. They DO wear out and they DO cause overheating (at idle).
06-17-2015 12:56 PM
emmo Yep. Heres another guy that has, more than once, cut the shroud to facilitate removal. It does the same job when reinstalled and taped. I think I took some small screws and fitted a neat plastic patch across the cut to repair it. But if you clean it well, quality tape will suffice.
If any part of the shroud, or the foam strips around the radiator , are missing at the end of the job, you will probably risk overheating.
09-25-2007 02:25 PM
kdavis
Quote:
Originally Posted by lawdogg
That's the piece I couldn't get off. Which ultimately led me to take it to the shop.
Shop? What shop? Someone please hand me my sawzall! Nice thing about my ZJ being my 2nd vehicle with 185k miles. It was part of fixing a water pump leak, which was a pain overall anyway, so cutting the shroud was just a small part of the bigger process.

Every time I work on the engine on the ZJ, I long for the days when I could literally crawl into my compartment of my 67 Chevelle and sit in there to work...
09-25-2007 02:21 PM
lawdogg
Quote:
Originally Posted by kdavis
The bottom part of the shroud is a huge pain in the butt. I ended up cutting a slit in mine on one corner, just so it was easier to get in and out...did this a long time ago, saved a bunch of trouble on future projects. just allows you to open it up to get it passed the fan and get it out. Not recommending it for everyone, but sure worked well for me. I still get the shroud protection, but not the pain.
That's the piece I couldn't get off. Which ultimately led me to take it to the shop.
09-25-2007 09:36 AM
kdavis The bottom part of the shroud is a huge pain in the butt. I ended up cutting a slit in mine on one corner, just so it was easier to get in and out...did this a long time ago, saved a bunch of trouble on future projects. just allows you to open it up to get it passed the fan and get it out. Not recommending it for everyone, but sure worked well for me. I still get the shroud protection, but not the pain.
09-25-2007 09:33 AM
FPKites Keep the shroud intact. Protects the lower fins from debris bouncing up, as well as directing air where it's supposed to go. You can hold it back easy enough when you're pulling the radiator.

Or you can do an e-fan swap. A bit more challenging due to the 4.0 length, but doable.
09-25-2007 08:41 AM
Mustang Thanks for the help
I got the old one out last night and am planing on puting the new one in today. Best way to go for me was to remove the small front skid plate it opened every thing up and made getting those bottom hoses(Transmission/Coolant) off easy and draining the old coolant. The only problem was with the fan cover(Belt driven fan) was a pain because it would get in the way and it would not come out until the radiator was out. It goes all the way around the radiator. I was thinking about possibly removing the bottom part of this cover and just keeping thetop part that keeps your hand from hitting the blades. to make things easier. any ideas? or do you think i should keep the whole thing intact
09-24-2007 04:48 PM
Vestjam It's very straight forward. Obviously you want to wait until the vehicle has cooled off.

Disconnect the hoses, remove fan (if attached to radiator). Remove the top radiator bracket and the whole thing will slide out. IF you have the radiator that has the transmission cooler as part of it, you'll have to disconnect those lines also (obviously).

A radiator shop can clean or repair it, but a new one will not be much more. I purchased a new one for $159. Don't order from a dealer $$$$$.

If it had been running hot, now might be a time to consider new thermostat also. ALSO, If you have the time, you could pull the water pump and flush with water to remove any residual debris in the system... Just a thought...
09-24-2007 12:44 PM
sandman i did mine on my xj and if i remember right all i did was disconect the hoses, un bolt the top support and it slid right out it was easy.
09-24-2007 12:39 PM
lawdogg I took mine to a shop to do it, but the repair manual give you good directions.
09-23-2007 09:07 PM
Mustang
93 jeep grand cherokee(4.0) radiator needs to be replaced

I was wondering if any one had any good advice or any good links on how to replace this radiator

Thanks

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome