JeepForum.com - Reply to Topic
Thread: Front Axle Hub Bearing Flange Question Reply to Thread
Title:
Message:

Register Now



In order to be able to post messages on the JeepForum.com forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid e-mail address for yourself.



Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
10-21-2019 03:37 PM
2jhanna Thanks Blaine and others for the input. When I first saw the different flange mountings, my first thought was, "that's not right, I need to fix it". Then my second thought was, "it's been that way for 17 years, and if it ain't broke, don't fix it".

I do see where the flange toward the hub bearing would offer more protection, and if I ever have that side apart, I can "fix it" at that time.
10-21-2019 11:25 AM
TheBoogieman
Quote:
Originally Posted by mrblaine View Post
They are essentially a useless artifact from the older spindle and wheel bearing design so it makes little difference how they are mounted.
Glad to see you posting here again. I thought you got sick of stupid questions. Real experts are rare IMO.
10-21-2019 10:27 AM
mrblaine
Quote:
Originally Posted by 2jhanna View Post
I just find it really odd how inconsistent the orientation is. Not only from year to year, but even within a year like my 02. I have every reason to believe that my axles are not only original but have never even been removed before this past week.
They are essentially a useless artifact from the older spindle and wheel bearing design so it makes little difference how they are mounted.
10-21-2019 10:10 AM
TheBoogieman
Quote:
Originally Posted by 2jhanna View Post
thanks. this explains everything and it makes total sense now. since you have a 00 and a 05, it makes perfect sense that my 02 was the "transition year". that's why one side is one way, and the other side the other way.
I always thought my TJ was special.
I guess that's why my Jeep built in June of 02' has one square mirror and one rounded style one. Thanks for clearing that one up for me. A transition year special Jeep. I thought the PO was just too cheap to buy two.
10-21-2019 09:53 AM
TheBoogieman My 99' and 03' both look like the right side pic.
10-21-2019 09:13 AM
2jhanna I just find it really odd how inconsistent the orientation is. Not only from year to year, but even within a year like my 02. I have every reason to believe that my axles are not only original but have never even been removed before this past week.
10-21-2019 07:58 AM
mrblaine
Quote:
Originally Posted by 2jhanna View Post
I pulled my front axle shafts to change the inner seals. I noticed that on the 2 axles, the flange behind the hub unit bearing was facing differently, as shown in the picture below.

Unless this was done, one side reversed, during the first 5 years of its life, I assume it came from the factory this way.

Not that I going to change it, but which way is correct? The shaft on the left with the red showing is the driver's side.
Neither is actually correct for a sealed unit bearing. One can make a case that the flange on the slinger is doing some good acting as a debris guard when it is close to the back of the UB but that's it. The other one is wholly wrong since it is a carryover from an actual spindle and locking hub design and it carried a V seal that butted up to the back of the spindle to keep water/dirt out of the bearings. Without the V seal and the big gap between the flange and the back face of the UB, it is useless.
10-19-2019 04:08 PM
2jhanna
Quote:
Originally Posted by mukluk View Post
Just checked both Jeeps: on the '00 that I've owned since it had two miles on the clock and know both axle shafts are original, both flanges face the axle u-joint; on the '05 that I've owned since 34k miles on the clock and believe both axle shafts are original, both flanges face the hub. I guess you can take your pick which direction the flange faces.
thanks. this explains everything and it makes total sense now. since you have a 00 and a 05, it makes perfect sense that my 02 was the "transition year". that's why one side is one way, and the other side the other way.

the passenger side axle shaft assembly line got the memo before the drivers side axle shaft assembly line.

I always thought my TJ was special.
10-19-2019 12:16 PM
mukluk Just checked both Jeeps: on the '00 that I've owned since it had two miles on the clock and know both axle shafts are original, both flanges face the axle u-joint; on the '05 that I've owned since 34k miles on the clock and believe both axle shafts are original, both flanges face the hub. I guess you can take your pick which direction the flange faces.
10-19-2019 07:02 AM
2jhanna
Front Axle Hub Bearing Flange Question

I pulled my front axle shafts to change the inner seals. I noticed that on the 2 axles, the flange behind the hub unit bearing was facing differently, as shown in the picture below.

Unless this was done, one side reversed, during the first 5 years of its life, I assume it came from the factory this way.

Not that I going to change it, but which way is correct? The shaft on the left with the red showing is the driver's side.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome