JeepForum.com - Reply to Topic
Thread: Wiring LED's into high beam circuit Reply to Thread
Title:
Message:

Register Now



In order to be able to post messages on the JeepForum.com forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid e-mail address for yourself.



Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
07-11-2019 10:27 PM
yoyoyo109 Well glad to see my image post actually went through. I was successfully able to use the high beam to trigger my relays but I'll be soldering a 6800uF capacitor in tomorrow to mitigate the flickering to the LED's
07-11-2019 10:07 PM
yoyoyo109 Test
07-08-2019 11:11 AM
cranbiz If the wires from the relay to the lights is not heavy enough, you will generate heat. That heat can be enough to melt the connector plastic. Up the size of the wires to the lights to decrease the resistance.
07-06-2019 04:22 PM
yoyoyo109
Quote:
Originally Posted by Kruzin View Post
A single relay will be sufficient, and probably better since the TIPM is very sensitive to current draws. You want to stay as close to factory specs for current draw on any circuit you tap into.
You don't think there could be issues with power supply?

Before starting this rewiring process I had two lights on one relay each and I've noticed the plastic on the connector for each relay has become very warped as though it was slowly melting. I had assumed the heat was just too much for the connector to handle, I plan on reusing the relays but using shielded female connectors to connect to them.



If one 30/40A relay is really all that's necessary however, that would make the installation significantly easier.
07-03-2019 01:49 PM
Kruzin A single relay will be sufficient, and probably better since the TIPM is very sensitive to current draws. You want to stay as close to factory specs for current draw on any circuit you tap into.
07-03-2019 01:34 PM
yoyoyo109
Quote:
Originally Posted by cranbiz View Post
As long as a single relay has enough current capability, I would use just 1 relay for both lights. Only power the relay coil from the high beam circuit, power the lights from the battery.
Sorry, I misspoke. One relay per pair of lights, one light draws 80W 5.79A so each pair draws 160W ~12A
07-03-2019 01:17 PM
cranbiz
Quote:
Originally Posted by yoyoyo109 View Post
Thanks for the response. I have one relay per light pod. Should I tap one into each high beam to make sure the brightness is the same? Or will the draw truly be so negligible that it won’t impact one high beam to have two relays signaled from it?
As long as a single relay has enough current capability, I would use just 1 relay for both lights. Only power the relay coil from the high beam circuit, power the lights from the battery.
07-03-2019 01:05 PM
yoyoyo109
Quote:
Originally Posted by cranbiz View Post
The signal comes from the PCM to the relay in the TIPM. That relay is soldered onto the PCB in the TIPM. Just tap into the high beam wire. It's a PWM source but if you use a relay, the draw will be negligible.
Thanks for the response. I have one relay per light pod. Should I tap one into each high beam to make sure the brightness is the same? Or will the draw truly be so negligible that it won’t impact one high beam to have two relays signaled from it?
07-03-2019 12:52 PM
cranbiz The signal comes from the PCM to the relay in the TIPM. That relay is soldered onto the PCB in the TIPM. Just tap into the high beam wire. It's a PWM source but if you use a relay, the draw will be negligible.
07-03-2019 10:09 AM
yoyoyo109
Wiring LED's into high beam circuit

Hi everyone, I was looking for information on wiring my LED pods into the circuits for my high beams while also maintaining the manual turn on switch I have.

I know that the amperage draw from the relay should be negligible but I wanted to confirm that it shouldn't be enough to cause flickering in my JW Speaker headlights. If so, I was wondering where the best place to tap into the "High-Beam Turn-On" signal would be

Since I will have two input sources going to the relay, I will be splicing a positive diode into the signal wire coming off of the high-beams. That way if I turn the LED's on manually my high-beams should not also turn on.

TL;DR Where is the best place to get a relay turn-on signal from the high-beams turning on?

Thanks!

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome