JeepForum.com - Reply to Topic
Thread: Clutch Switch Reply to Thread
Title:
Message:

Register Now



In order to be able to post messages on the JeepForum.com forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid e-mail address for yourself.



Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
06-30-2019 01:11 PM
RubiT To keep everyone posted, We finally have it running again!! Yeah. We replaced the clutch safety switch since that was broken. Then it still wouldn’t start, ended up replacing the electric ignition actuator. It started at that point. But upon moving it outside of garage noticed the battery wasn’t holding the charge and upon closer inspection the battery also had a loose connection. With that tighten and all the new parts, hopefully we’ll good to go for awhile.

Thank you all for the helpful tips and ideas. They were all greatly appreciated!!

Happy Jeeping!! 🚙
06-27-2019 08:06 AM
Zeep This has always confused me. My '05 LJR has no terminal contacts in the #28 slot.
I ended up disconnecting the switch under the steering column, and jumping the harness.

This has been working for me 10+ years.
06-25-2019 03:23 PM
mukluk Installing the fuse in PDC slot 28 will allow you to start the '05/'06 Jeep with the clutch pedal out, regardless of transfer case or transmission position. The note about 4L only is a CYA safety note trying to keep people from leaving the switch defeated all the time.
06-25-2019 02:51 PM
Rubi4MyMrs True according to the 2005 Owner’s manual, & you must be in 4Lo for it to work but this is in the 2006 manual p. 187…

Clutch Interlocking Ignition System (Non —
Rubicon Models Only)
Manual transmission vehicles are equipped with a clutch
interlock safety feature. With this feature engaged, you
must depress the clutch pedal to allow cranking of the
engine. To temporarily bypass this safety feature while
off-road driving (4L range only), which will allow cranking
the engine without depressing the clutch, follow
these steps:
1. Locate the Power Distribution Center (PDC) in the
engine compartment. Refer to “Fuse Panel” in Section 7
of this manual. (See page 305 for more information.)
2. Put a 10 Amp fuse in the PDC cavity (#28) marked as
Clutch Override.
NOTE: A fuse is provided in fuseblock cavity (f19 or
f20) marked as Spare.


So??? I do know jumping the switch will work.

06-25-2019 02:17 PM
mukluk The clutch interlock switch defeat for '05 and '06 is via installing a fuse in PDC slot 28, marked as "Clutch Override".
06-25-2019 11:15 AM
jtec as mentioned jumping the CPPS will bypass.
Attached diagram should help.
let us know.

FYI the CPPS is part of clutch 'master' or hydraulic cylinder.
06-25-2019 11:04 AM
Rubi4MyMrs There is no fuse 20 bypass for ’05 & ‘06s.

I don’t know how the clutch switch works (I have an auto) but if in doubt you can unplug the connector to the switch & put a jumper wire across the 2 terminals in the connector. Then see if it starts. If not, the problem is not the that switch.

If you are getting the (normal) cluster lighting up when you turn the key on but nothing from the starter when you turn to start the most common reason is a broken actuator tip. Here is a link to easily check it & how to start it if it is broken.

https://www.jeepforum.com/forum/f9/0.../#post40566713
06-25-2019 10:15 AM
RLD831 I can check if mine does when I get back to my Jeep later, but for now you could install a fuse in the clutch override, behind the glove box. That will bypass the check entirely.
06-25-2019 09:13 AM
RubiT
Clutch Switch

Own a 2006 Rubicon, which at the moment won’t start. Wondering if the clutch switch should slide up and down on the rod?

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome