|Topic Review (Newest First)|
|05-22-2019 07:12 PM|
Thank you very much. I will definitely check this cruthchfield web site. I think I can cut opening with no problem. I have tools and skills to do it and would like to go with 2 DIN size system. Form what I see basically any system will work with my Jeep.
Thank again for recommendation.
|05-21-2019 11:25 PM|
Bit hard to not go to a double DIN size head unit and best bet there rather than hacking away is to get a kit like this one. But is $100 of your budget right there
To get an idea on what will fit and what will be needed to do so check out https://www.crutchfield.com/car/outfitmycar/mycar.aspx
Sounds like you have the no NAV no Boston A. set up. Looks like some decent heads for our $300 target but like mb81 mentioned you'll probably need some bits to make it all work. The crutchfield.com site will give what is needed for the install. Once you find something you like there i would shop it to see if you can find it less elsewhere as Cruthchfield is normally no the lowest but might price match. But a real good place to start to see options on what will work.
|05-21-2019 07:37 PM|
|yzjwk||I have no experience with the non amp system so hopefully someone in the know will chime in but I would say Yes I think you would just need a wiring crossover plug or factory radio pinout to tap in to the connector.|
|05-21-2019 05:35 PM|
No there is no amplifier.
So it is mean that I can put there any system as long as it fit in?
|05-21-2019 09:54 AM|
Originally Posted by wojtek90 View Post
Take a look in the rear hatch, left hand side panel I believe, and see if you have an amplifier back there. You should be able to see it through the vent slots without removing the panel.
|05-20-2019 11:19 AM|
|wojtek90||Thank you. i will check it out. What I supoust to watch for set up. I never done it before and not familiar with radio connection. Can you please elaborated more about it.|
|05-20-2019 11:12 AM|
Originally Posted by ggrassmid View Post
|05-20-2019 08:14 AM|
Whatever you buy, do not get a MyGig REN unit:
1. No GPS.
2. Have never been successful getting Sirius and the REN to work at the same time. Right now, I have all of the right hand side speakers out, even though the displays show it working. No codes.
3. Had the head unit, speakers, a cable, and the Boston Acoustics amplifier replaced at various times.
4. There is an entirely separate set of owners manuals for this POS. They didn't come with delivery and I only found it by accident.
5. Someone disconnected the battery without pulling the radio fuse first and it seems to be fried (see applicable REN TSB).
This setup has been FUBAR since I got it. I asked MOPAR several times to replace it with the RER version but they refused. Maybe I will give it 1 more shot at testing the amplifier output. Even the '08 MOPAR WK FSM is very sketchy on this. The signals run through the CANBus, not traditional wires.
Current solution: Leave the [email protected]#$%&* radio off. It's a very expensive clock.
|05-20-2019 06:59 AM|
|mb81||Kudos if you can stick to that budget! When doing mine I found the harnesses to integrate the steering wheel controls and can bus interfaces, etc were almost $200 by themselves. Maybe you're not counting those costs in your total? Not sure what head unit you're looking at, but you might be able to find something you like for $300. I had the same radio in your picture and I considered a Seicane unit (android) because it looked to fit the best and have plenty of features. I didn't end up going that route and the longer I went the more money I spent on the project. The factory audio system is tricky on these! Know what setup you have first.|
|05-20-2019 06:25 AM|
|ggrassmid||your picture is upside down... fyi|
|05-19-2019 01:18 PM|
New radio GPS and Camera for Jeep
Finally is time to put new audio and GPS system in my Jeep Grand Cherokee 2007 3.0L disel . It is hundred of them on the market, but I would like to have your opinion guys which one to chose.
I am thinking about Android based system with ability to connect all steering switches and budget about $300. I don't mind to do some cuts in original opening.
Please help me with selection.
Sorry for up side down picture. I do not now how to rotate it.