|Topic Review (Newest First)|
|06-02-2019 06:36 PM|
I took off later this week and will bring it to a mechanic that was recommended by a coworker. I’m assuming I’ll have to leave it overnight so they can replicate the problem in the morning unless something just sticks out to them.
Until then I just hope it keeps on bringing me to and from work!
|06-02-2019 04:17 PM|
|ColdCase||Ran over a can?|
|06-02-2019 03:13 PM|
Well, pulled into a parking spot today and had a loud singular crunching pop sound come from underneath. I couldn’t tell if it was from the front or back. I am more inclined to believe it was the front as I had just cranked the steering wheel and let off the brake to pull into the spot when it happened. Either way, seems indicative that one of the CV joints on a half shaft is on the way out.
I found an empty lot and made a BUNCH of circles forwards and backwards and everything in between trying to replicate it later on but never heard it again. I did have a few clunks when first accelerating from stops here and there, but nothing crazy.
|05-29-2019 07:17 PM|
I suppose the suspension was hanging when up on the lift? That may put the half shafts and CV joints at an angle where the vibration is worse, more easily detected.
The vehicle dynamics on a lift is a bit different than on the ground or dyno, however
|05-29-2019 06:44 PM|
Last weekend, I put the vehicle up on a lift thinking I’d get it up to 45mph to look for a cause. I couldn’t get it up past 15mph before the whole thing started to shake violently.
I lowered it back down and did a visual inspection, but everything looked fine. I went on a quick test drive and the vibration was gone. Of course later in the day once the car cooled off it came back.. but very interesting.
So far have eliminated and or replaced:
Front and rear drive shaft
I guess next I’ll start on the CV axles. Those are the only damn things left that spin while driving short of the gears in the front and rear diff and the transmission. Those all seem fine... thankfully.
|05-24-2019 02:30 PM|
|05-24-2019 01:26 PM|
The WK2 shudder is different than the TQ lockup shudder that the Liberty has. Perhaps a sticky transmission or transfer case clutch when cold/dry.
From what I've read here, unless its a tire thing the easiest and, on the average, the most cost effective way to solve a WK2 vibration is to trade it off on one that drives smooth.
|05-24-2019 10:30 AM|
This would be so much easier to solve if it didn’t go away after a few miles. I’m assuming something is getting coated after fluids warm up or a bushing is more flexible after warming up.. it’s been roughly 90 degrees outside lately so its not exactly cool conditions.
I was really betting on the CV joints on the rear shaft being bad, especially since the grease had been leaking, but the new shafts made zero difference. Further inspection on the old shaft, center support bearing, and guibo (flex disc) all looked decent too.
I would think “hope” if it was the front or rear differential, it would be a constant problem.
Transmission shifts smoothly, fluid looks clean and is full.
I may try to bring it by an independent mechanic to get their opinion before selling it. I’ll end up losing some decent $ if I sell now as I paid right at KBB value for it. The rest of the Jeep is immaculate at least.
|05-24-2019 09:32 AM|
Originally Posted by simmons1183 View Post
|05-23-2019 07:35 PM|
OP got a QTII which you can drive with the front driveshaft off, but not the back. Its basically a 2WD Jeep with a power takeoff.
The 2011-2013 transmissions can shudder a bit for the first few miles (mine does this once in awhile, although not near as severe as yours, its heard but not felt). Our 09 Liberty's lockup converter shudders all the time, which is considered normal for that V6 transmission. The transfer case clutches can shudder. I forget if you said you checked/changed fluids. The rear axle usualy just bumps, doesn't shudder.
Solving WK2 vibrations can be a challenge, many here have given up.
|05-23-2019 06:49 PM|
Take one drive shaft off and drive it, see if the vibration goes away, then do the same with the other. Wait, can you even do that with a full time 4WD Jeep? Would be one easy cheap way to rule out a drive shaft. Maybe a differential/differential bearing, wheel bearing, transmission mounts, hard to say.
Take it to a tire shop and have them verify its not your tire/wheel combination.
As for those drive shafts being serviceable, they're not they're replaced as a unit....however, for a permanent solution to that serviceability issue, go to a driveline shop and have them build drivelines to fit your Jeep with the U-Joints and adapters for the transfer case and differentials, and you'll never have to deal with that issue again in the future. Had that done on my Bronco 2 as it had a similar type of driveline in the rear of it which wasn't repairable. It was a bit expensive but worth it for future repairs where I can now pull the driveshaft and simply replace U-Joints.
|05-23-2019 06:37 PM|
I hate to give up.. but I am almost $1000 in now and am all but ready to just see what car deals can be had this weekend.
None of the dealerships in my area are worth anything or I’d just bite the bullet and bring it there. I had hell fighting them over different things that went wrong with my JK.
|05-23-2019 07:37 AM|
|ColdCase||I had bad tires a couple times that gave me the same/similar vibration symptoms you describe. Vibrations come and go what seemed like randomly. Disappearing for days. Look for a wheel with a large amount of weights or on different edges. Different alignment specs created slightly different response, but it didn't matter what corner the tire was on. The clunck is something else. You did check the lug nuts?|
|05-23-2019 07:16 AM|
Sorry for multiple posts, I am still not allowed to edit/delete.
I started the engine and let it warm up this morning before driving... no change. I am now starting to feel a little vibration from the engine at idle from the mount, but no change in the drive line vibration.
I am also hearing the driveline vibration at highway speeds, but can barely feel it once going 60+
Still goes away after a few miles and does not return until car has been sitting and cooled off
|05-22-2019 10:40 PM|
|simmons1183||Maybe the leaking motor mount is related...|
|This thread has more than 15 replies. Click here to review the whole thread.|