JeepForum.com - Reply to Topic
Thread: MyGig anyone? Reply to Thread
Title:
Message:

Register Now



In order to be able to post messages on the JeepForum.com forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid e-mail address for yourself.



Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
12-04-2016 02:01 PM
rickou812 I have a 2011 wrangler unlimited with the RHB unit. It had software vers. 20.xxx on it and travel link would not work. I downloaded an update iso for 33.xxx update and burned a cd-r. I loaded the disk and and followed the update prompts. It is now in a never ending boot loop. The JEEP boot screen displays and stays on for about 30 seconds then the unit turns off and repeats... None of the buttons work. I can not get the cd out..etc.
I have tried pulling the fuse etc.. I have even disconnected the battery for over an hour with no change.

Is there any way to get the cd out?
Is there anything else I can do to try and recover the unit?

Thanks in advance for any help
Rick
07-07-2014 07:35 PM
jschwab1
Quote:
Originally Posted by amr42 View Post
Well if the unit has been replaced and the ground wires confirmed good, then it can only really be the power (+12V) supply that is being interrupted on the bump... What about fuses? Tried to rule out them? I've never heard of a bad fuse connection, but it's worth a try...
Does the 430N unit have it's own 12V power supply? There does not seem to be a fuse for it within the TIPM box on my 2014 JKUR.
07-07-2014 06:31 PM
amr42
Quote:
Originally Posted by jschwab1 View Post
I have a 2014 JKUR with 430N unit with a problem I can not seem to solve and I am hoping someone here can advise. Jeep has replaced the nav unit and worked on ground wires. When I hit a bump in the road the right way, the 430N cuts power and reboots. Why is it doing this and what can be done to fix it? This happens several times on each drive. A solution would be amazing!
Well if the unit has been replaced and the ground wires confirmed good, then it can only really be the power (+12V) supply that is being interrupted on the bump... What about fuses? Tried to rule out them? I've never heard of a bad fuse connection, but it's worth a try...
07-02-2014 10:56 PM
jschwab1 I have a 2014 JKUR with 430N unit with a problem I can not seem to solve and I am hoping someone here can advise. Jeep has replaced the nav unit and worked on ground wires. When I hit a bump in the road the right way, the 430N cuts power and reboots. Why is it doing this and what can be done to fix it? This happens several times on each drive. A solution would be amazing!
06-06-2014 10:39 AM
alben Do you know what year the RER radio was manufactured? I can't recall if it is the year of the radio or the year of the vehicle, but at some point Mopar tied the vehicle VIN and the radio together so that only a dealer could make a radio swap. From what I read it was to discourage theft. Google it and you might come up with something related to this topic. Also you might want to consult your local Mopar dealer.
06-05-2014 01:17 PM
kevinwayne20 I just purchased a RER unit (5064080AB a High SPD Buss unit) off of Ebay to put into my 2012 JKU. I plugged the unit in and the screen was blank. A fan kicked in on the side but I couldn't get it to do anything else. I took it out so I could do some more research on it thinking I may have screwed up and got the wrong unit. If that was the case, I was going to bite the bullet and resell it back on ebay as it would have been my mistake.

I looked through this thread and countless others and didn't see anywhere that the old RER units wouldn'g work in the 2012's. Did I miss it or should it work? I'[ve got the convinence package if that helps. For a short time after I traded in my 08, I had a REN unit in it so my gut says I've got a DOA unit t hat I need to send back to the vendor.

Any help is greatly appreciated!
05-29-2014 01:25 PM
gumbydammit Anyone install a switch to interrupt power from the infamous J13 or have tips on how to do that??

Sometimes my RER will run for weeks without having to reset it, however the last couple of weeks (since it's been parked outside interestingly enough) I have to pull the fuse every time I get in it, otherwise I get a blank screen. Pushing the nav/menu buttons will make the Jeep logo come up, but that's it. Once I pull the fuse for a few seconds I'm good to go again... for a while.

I'm considering putting a small switch under the dash that will interrupt/disconnect whichever line leads to the J13 fuse so I can reset it from inside the cab. As it is, I'm going to wear out my hood hinges and the lid to the fuse box!
12-18-2013 06:01 AM
08blkjk
Quote:
Originally Posted by meon2wheels View Post

I would pull the fuse for 5 mins, put it back in and try again. This worked for me.
Thanks, I'll give it a shot.
12-17-2013 10:11 PM
meon2wheels
Quote:
Originally Posted by 08blkjk View Post
I have an 08 with the RER. Tonight I pudhed the open close button and the screen went blank and nothong happened. I manually pulled the screen open and got the CD to load. I pushed the button again and nothing happened. I again manually pushed the screen closed and still nothing. The only button that works is the U Connect button. Thought or suggestions?
I would pull the fuse for 5 mins, put it back in and try again. This worked for me.
12-17-2013 06:14 PM
08blkjk I have an 08 with the RER. Tonight I pudhed the open close button and the screen went blank and nothong happened. I manually pulled the screen open and got the CD to load. I pushed the button again and nothing happened. I again manually pushed the screen closed and still nothing. The only button that works is the U Connect button. Thought or suggestions?
08-18-2013 10:17 PM
AlbertaJeeper Hey everyone, I'm having troubles with my 430 (RHB) on my '13 JKUR not ejecting the disk. The cover slides down a tiny bit and kicks back up again. Any tips?
06-11-2013 10:27 AM
jryano Well it's been about 2 months and I'm getting ready to go on vacation. I took my RER out and put in the original 6-disc. It worked for about 2 weeks then it started the same thing. So it's obviously not the head units. Can it be something wrong with my computer or the CANBUS system? I just don't understand how sometimes it comes on and others it won't. But it never stays on more than about 1.5 hours. All of the fuses I have checked have been fine.
04-07-2013 08:36 PM
jryano Be lucky that you're getting three weeks. I literally get 20 minutes of use and then it might not come back on for a day or more. Mine is off more than its on.
04-07-2013 08:24 PM
meon2wheels Mine repeats every 3weeks or so, curious how you make out.
04-03-2013 09:03 PM
jryano
Quote:
Originally Posted by SirCody

Sounds cool...and we'd be able to rule out any problems it being in your wiring etc and know that it's the Unit and not internal of the Jeep...I will have a couple MyGigs we can plug into your jeep ...Gonna send you a PM with My Text
Ok so it's working. I removed the RER, then pulled the J13 fuse let it sit, put the RER back in, and then put the J13 back in. It's working fine as of right now. I've taken a pic of the system info.
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome