JeepForum.com - Reply to Topic
Thread: Comanche Leaf and Shackle Reply to Thread
Title:
Message:

Register Now



In order to be able to post messages on the JeepForum.com forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid e-mail address for yourself.



Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
07-12-2019 08:17 AM
jkufrancesca Yeah I’m just curious I bought the same ones yesterday part number ropcom35-0 and was told they were removed from a Comanche but the shackle on them adds another 4” of lift I just bought the springs for a solid four so curious if the stock would be problematic. But I’ll try and get to them today with some weight
07-12-2019 06:02 AM
CJ7-Tim It is very common for XJ and MJ leaf springs to "seem" to be too short. Often I have had to install the front bushing bolt and then lower the Jeep to put weight on the leaf spring to install the rear bolt. You do have to be careful the Jeep doesn't fall off the jack or jackstands, and that you don't get your fingers or hands caught between the springs and other hard stuff.

Obviously the larger bushing is the front bushing, so you really can't put them in backwards.
07-12-2019 04:23 AM
jkufrancesca Did you ever figure it out?
01-26-2015 06:24 PM
cyclejeep It appears that XJ spring #s are ROP-XJ45-0. I missed Rustys on the phone today. I'll try back tomorrow and report! Thanks guys.
01-26-2015 05:53 PM
Motorcharge Yeah I got nothing on the part number either though I do see it in the picture. Just looked at mine and the short side is forward. MJ leafs are significantly longer than XJ leafs are and one side is obviously longer on them. As for the arch in them, they should have a lot more than factory with a spring under setup. Having no weight on it might make some difference but not that much. Even when I have mine on a lift at work the shackle isn't touching the frame.

They've got to be XJ leaf packs. If they were on backwards the axle would be pushed noticeably too far back. If they're XJ leafs they'd be too short and pull the shackle forward like they're doing.
01-26-2015 08:58 AM
LAF1269
Quote:
Originally Posted by cyclejeep
I'm confident that the spring is in the correct direction. The spring part # is ROPCOM35-0. When measured along the leaf, they are the same dimensions as the factory springs. However, they are significantly more curved.
I checked Rusty's site and couldn't find a match for that part number. Google came up with nothing also. There was a photo of an XJ 4.5 kit that had a legible part number on the spring that read ROP-XJ45-0. If that part number code applies to all of their kits then it looks like you don't have a 4.5 inch spring. I'd call Rusty's and have them sort it out for you.
01-26-2015 08:20 AM
cyclejeep Thanks for the feedback Motorcharge. There is a variation in length between eyelet and centering pin (26" and 31"). Even before mounting the axle, the length demands that the shackle be forward which tells me that the eyelet to eyelet length may be too short...or am I missing something else. Must the axle be mounted before attaching the rear leaf to the shackle?
01-26-2015 08:14 AM
cyclejeep Picture from the rear showing springs.
01-26-2015 08:14 AM
Motorcharge Then they must be backwards. They shouldn't be centered on the axle. There's a short and a long side.
01-26-2015 08:09 AM
cyclejeep I'm confident that the spring is in the correct direction. The spring part # is ROPCOM35-0. When measured along the leaf, they are the same dimensions as the factory springs. However, they are significantly more curved.
01-25-2015 09:44 PM
LAF1269 If I had to guess, I would say that you might have XJ leaf packs on there. What's the part number on the leaf spring?
01-25-2015 06:59 PM
Motorcharge You don't have the leaf packs on backwards do you? And you did order the Comanche and not Cherokee leaf packs right?
01-25-2015 02:50 PM
cyclejeep
Comanche Leaf and Shackle

I've got a 1989 comanche that I am attempting to install a Rusty's Offroad Products 4.5" lift. Front end is complete which was a total piece of cake thanks to all of the anti-seize used at the factory The rear end is another story. The spring pack has considerably more arch and as such requires that the shackles be pulled so far forward as to touch the frame (not good). Anyone run into this problem? Solutions?

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome