JeepForum.com - Reply to Topic
Thread: Anyone ever make a case spreader? Reply to Thread
Title:
Message:

Register Now



In order to be able to post messages on the JeepForum.com forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid e-mail address for yourself.



Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
07-01-2012 03:40 AM
rixcj When I rebilt my front axle, I hooked up a come-along to the axle tube yokes, and ran the cable across the backside of the axle. I set up a dial indicator to make sure that I didn't overdo it. It didn't take but a few thousanths of spreading to get the case out. It worked great.

Rich
06-22-2012 11:05 AM
dbhammer
Thank You

Thank you JLC08JK for the picture. I'm tearing into my Daughters 2004 TJ front end this weekend. Trying to take care of a hum / vibration. I'm pretty sure it's the unit bearings (wheel hubs) and have all the parts to replace these. While I'm in there I'm going to replace the axle u-joints and fix a leaking inner oil seal. To get to the oil seal I have to open up the diff and pull out the carrier. This will be my first time into a differential so I'm a little nervous. This forum has been a fantastic source of information and I'll plan on building a similar case spreader to make my life a little easier.

I'll let you know how it goes.
06-08-2012 02:59 PM
JohndKc
Quote:
Originally Posted by gabriel05 View Post
Personally I don't think you will need it to do the gears. When I installed the Truetrac and Ox in my jeep I just wrapped a strap around the carrier and then hooked a slide hammer to it. It was able to pop the carrier out pretty easy. However, if you feel like being creative go for it. I've made plenty of little gadgets knowing that they might not be needed, but it was fun nonetheless. Post pics if you end up making one.
Its for setting carrier bearing preload. Never used mine to take out a carrier, just used it to set the recommended preload on both of the carrier bearings.
06-08-2012 01:41 PM
SubAtomicGenius ^^^ Doing this when I get home on my rear axle assembly, I'll be referencing your thread, Jim. I'm making a case spreader because ARB specfies that you MUST use one. Lots of nay-sayers out there that say you don't, however I'll be using one.
02-28-2011 07:21 PM
mike481 Since I'm going to be removing the axles to do the ARB's I'll try it without the spreader first. If I have any issues what-so-ever I'll go ahead and make the spreader. Some guys have said to use a shim driver but if I need to use one I'll go with the spreader instead. It's going to be the fist of April before I get all my stuff so I have time to get prepared.
02-28-2011 01:31 PM
JLC08JK I found that it made the ARB install go smoothly.
The arb uses the shims on the outside of the bearings so if you try and pound the whole thing in, there is no way to keep the master shims in place.
With the spreader I was able to set the carrier in place and slip the last shim down the side.
02-28-2011 09:40 AM
mike481 I haven't made mine yet but I have everything I need except the bolts and pins. I found some grade 8 7/8"x4 bolts that I can cut the thread off and weld the remaining bolt to the back side of the spreader. Mine will look like the regular style spreader with a frame and a threaded bolt at the bottom to make it spread the case. I drew it up to work with any Dana up to a D60.

I'm waiting to see if I need it until I am ready to install everything with my regear/ARB install. If I do make it I will post up pics.
02-28-2011 12:47 AM
JLC08JK I made this one last week using 1-1/2" X 1/8" wall sq. tube.

It has 3/4" all thread at about 14" apart and long hanger-nuts to provide extra thread surface for the tension.
Make sure to put some anti-seize on the threads as it is under allot of force and don't spread the case beyond the recommended amount.
Mine said not to go beyond .02".
I used short pieces of the all-thread protruding 1/2" as you want the sq. stock to be flush against the case.
This was not over-built, the threaded bars were starting to bow as the pressure increased.
Good luck with your project
The link to mine is below.
02-11-2011 11:47 AM
gabriel05 Personally I don't think you will need it to do the gears. When I installed the Truetrac and Ox in my jeep I just wrapped a strap around the carrier and then hooked a slide hammer to it. It was able to pop the carrier out pretty easy. However, if you feel like being creative go for it. I've made plenty of little gadgets knowing that they might not be needed, but it was fun nonetheless. Post pics if you end up making one.
02-11-2011 10:56 AM
mike481
Anyone ever make a case spreader?

In the next month or so I will be re-gearing and adding ARB's front and rear. I was just wondering if anyone had made their own case spreader? I have an idea on how I am going to make it but just wanting to see if anyone has experience that can keep me from making something that isn't going to work well. It's a pretty simple looking thing but I don't want to reinvent the wheel if I don't have to.

Thanks

Mike

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome