JeepForum.com - Reply to Topic
Thread: Removing door molding on 97 XJ Reply to Thread
Title:
Message:
Post Icons
You may choose an icon for your message from the following list:
 
 
 
   

Register Now



In order to be able to post messages on the JeepForum.com forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid e-mail address for yourself.



Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
09-07-2012 06:56 AM
calvin196 Thanks so much for this post, I always looked at my faded gray plastic and said "Hm... I wonder how hard it would be to get this ugly plastic off" and for a while I was actually going to sand / paint them since I didn't want to damage my jeeps exterior. Anyways I followed your tut, and I love the new look on my jeep, thanks a lot!


here are pictures for before / after:
Before:
After:
08-10-2012 03:12 PM
castorriver Wow that really changes the look and for cheap!! Nice work.
07-17-2012 01:25 PM
Bigred95 I considered doing this to my 2001, but I'm afraid to. I fear that sticky residue will not come off. I worry because there is no play at all in those pieces of trim, they are on there good. Unfortunately they don't look good. I have a heat gun that worked great for decals and emblems, but I don't know if it's the same type of adhesive. Has anyone had any luck removing these with a heat gun?
06-08-2012 09:22 AM
kp954 goo gone cures all!
05-03-2012 12:37 PM
JHB625 theres a rubber wheel that body shops use works like magic. 100 times easier that a razor and goo gone
03-05-2011 03:27 PM
wmhuckabee i need to do this to mine some time, just pulled the molding off, never could get the rest off, not a bad way to do it. would of never though of this
12-03-2010 08:49 AM
AmbuGrl We used goof off and a flat razor blade..
11-28-2010 11:45 AM
dav5942 Great mod! Just did ours in 3 hours. Next need to open up wheel wells for 33" tires.



08-06-2010 12:04 AM
Mihogan Awesome writeup, I'm going to do this tomorrow!
08-26-2008 09:36 AM
JeepXJsport12
Removing door molding on 97 XJ

Let me start off by saying that this absolutly cost free mod is one of my favorites. Heres what was used-



- Skinny plastic object (I used a plastic light cover)

- Duck Tape

- Clear Box tape

- Soapy water

- Muscle Power

- Salvanise, To get off the little tiny bits of glue left behind (not necessary)

I started of by just pealing off the molding by hand. No heat gun was needed as the trim came off fairly easy. Here's what was left after pealing the molding off by hand.

I then used the soapy water and just cleaned the area off, there was alot of dust and dirt under the moldings. This also loosened up the 3M adhesive still left on the car.



I put togather the item i was going to use to very easily push the adhesive off with. It was the skinny plastic peice with 1 layer of duck tape over the edge and then a layer of the clear box tape. I needed the clear box tape over the duck tape b/c the duck tape would rip easily when pushed along the car and scratch the paint. The duck tape was just an extra reinforcemnet so that the tape would not rip. Here's what the tool looked like.

It was a little time consuming to do both sides but the end result was well worth my time. I think ti came out really good.



After all the adhesive was removed i used some salvanise (removes scratches and stains) to really clean the area off for a nice finish. The salvanise also removed some of the over spray that i had when i originaly rattle canned my trim. Here's the final results.


It's drying in the sun right now and then im going to have to wax the area around where the molding was b/c the salvanise stripped soem of the wax in that area.



Hope you liked it.



(still need a little more cleaning tho after looking at the pics)

Posting Rules  
You may not post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

 
For the best viewing experience please update your browser to Google Chrome