Jeep Enthusiast Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-18 of 19 Results
  1. XJ Cherokee Technical Forum
    Does anyone know of a "budget" upgrade for lower control arms? I have a 99 XJ with a 3in lift. The wheels are decentered to the rear and rub the corners of the fender flares every now and then. I trimmed the flares some, so for daily use it is ok. I'm not sure how it will do at full flex...
  2. General Jeep & Off-Road Equipment
    ...whoever put the lift kit on put longer lower control arms, but didn't put longer upper control arms." It's lifted about 3", with 16" fixed LCAs. :dunno:
  3. TJ Wrangler Technical Forum
    Hey guys, my tj has a 3" zone lift with stock control arms. it pulls right consistently, sometimes worse than others. I have had two alignments in six months. I started doing some more research, but couldnt find anyone with similar symptoms. It pulls whether im going 20 mph or 70. I am hoping...
  4. TJ Wrangler Technical Forum
    I have a couple that are seized and don't want to come free. Figured I would replace them all and keep the ones that come off as spares. I called the dealer with the part numbers this morning and after hearing how much they wanted ($160 for four bolts washers and nuts) I said I'll get back to...
  5. TJ Wrangler Technical Forum
    Im installing some rokmen control arms uppers and lowers and was wondering if anyone could save me alittle time and give me a length on the front lower control arms. Thanks
  6. TJ Wrangler Technical Forum
    I was wondering why in reverse if I hit a bump it would clank. I can move the rear upper control arm bolts by hand. These have never been touched so kinda odd but with all the work I did with JKS front/rear trackbars and quick discos should only take an hour max. Anything I am missing since I...
  7. TJ Wrangler Technical Forum
    I have a DC shaft and a SYE installed right now, they went in when my trans and t case were rebuilt, the plan was for a 2" lift and a TT sooner, but I got screwed over by a shop and that's where that money went. I have a DC shaft right now and an 8.8, I don't think my drive shaft angle is...
  8. TJ Wrangler Technical Forum
    So this morning I decided to drive to the gym, I pull out the driveway and as I shift into 3rd I feel the rear right side kick. I pull over, thinking I had a flat, and this happened. Now the average person would think some duct dape and guerilla glue would fix that right up, but me (the...
  9. TJ Wrangler Technical Forum
    I am hoping that someone can chime in providing input regarding moving the front axle forward ~1". What are the pros/cons of pushing your front axle forward 1"? Would I completely be screwing up my alignment, track bar location? At the moment I have adjustable control arms for the bottom...
  10. TJ Wrangler Technical Forum
    So I have developed a new noise after installing a bunch of parts. As the suspension cycles off road I can hear a clunk clunk. I just installed currie jj flca and I noticed tonight that the joints are not straight anymore. I assume that the joint is supposed to stay straight while the ??? PIN ...
  11. TJ Wrangler Technical Forum
    Purchased a used set of Teraflex monster control arms (lower rear) and not sure which end gets mounted to the axle? Flex end or the bushing end? Also does the grease fitting point up or down? Also any feedback regarding your experience with maintaining them?
  12. TJ Wrangler Technical Forum
    Would it be possible to add just lower long arms to a jeep, or would the geometry be off. I only ask because if it can be done. I thought it may make the rear a little more stable than a short arm.
  13. TJ Wrangler Technical Forum
    When i bought my jeep used it had a 3-4" lift, crappy adjustable LCAs in the front w/ stock UCAs. I since replaced the upper UCAs w/ adjustable ones because i had a bad bushing in the stocker, so it would be a good time to get adjustable uppers. I then noticed that my left lower control arm...
  14. TJ Wrangler Technical Forum
    Hey, I have been doing some research and found DND offroad, they will build me front and rear, lower, double adjustable control arms with Johnny joints at both ends for $450. They make them out of square tube which from what I've seen is best, any comments? Just wondering if anyone has used...
  15. TJ Wrangler Technical Forum
    I have a set of RE lower adj control arms I need to adj when I install my new currie arms, I have soaked the jam nuts in liquid wrench for a few days and now I want to see if I can loosen up the jam nut before I begin the tear down. Here is the problem, I forget which way the nut rotates to...
  16. TJ Wrangler Technical Forum
    I need to replace my rear lower control arm bushings on stock CA. napa says they only have the front ones and don't see a part for the rears. Are they the same size or do i need to speak with someone else at the Napa Store. I found them on their site so i can't see how they would not have...
  17. TJ Wrangler Technical Forum
    I need to replace the LCA brackets on my D30. Does anyone know what angle the factory ones sit at?
  18. TJ Wrangler Technical Forum
    01 tj 33s, im sitting at 3in sl and 1.25bl and i am putting 2in coil spacers in it, my question is control arms. I heard the front uppers can be fixed and the rear lowers can be fixed, and the front lowers and rear uppers need to be adjustable. But i would imagine they would all have to be...
1-18 of 19 Results
Top