Clay's Build Thread - Page 23 - JeepForum.com

Reply
 
LinkBack Thread Tools
post #331 of 5422 Old 08-28-2010, 03:16 PM Thread Starter
Skerr
Registered User
1985 CJ7 
 
Join Date: Sep 2008
Location: White Springs
Posts: 9,495
Quote:
Originally Posted by Jim1611 View Post
... By the way, it's in some the best deer hunting country is Missouri, thought that would be of special interest to you.
It certainly is! How much is land up there? Any acreage??


Kerrdog
Go Fish! <*////><

But the right word at the right time... "Hey, give me a little hug!" That's the difference between lightning and a harmless lightning bug!
Skerr is offline  
Sponsored Links
Advertisement
 
post #332 of 5422 Old 08-28-2010, 04:55 PM
Jim1611
Web Wheeler
 
Jim1611's Avatar
1985 CJ7 
 
Join Date: Jul 2009
Posts: 7,190
Quote:
Originally Posted by Skerr View Post
It certainly is! How much is land up there? Any acreage??
It's some of the more resonably priced in the state. The land east of there will get high, ie river bottom farm ground, and west of there I think it gets a bit cheaper. The general vicinity of it is rolling pasture and farm land. Some of the ground gets pretty rough too and it's only suitable for livestock grazing. What it doesn't have is the tourist attraction that the Ozark area and Branson has. They are pretty pricy. I haven't heard lately but in the past that part of the state was one of the few places land was still selling in the $1000.00 an acre range. Who knows Scott with a depressed economy there may be some bargains. Let me do some snoopin next week.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
(Crabtree Shackle Hangers)

My build thread

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Jim1611 is offline  
post #333 of 5422 Old 08-28-2010, 05:42 PM
FamillyCJ7
Registered User
1983 CJ7 
 
Join Date: Mar 2009
Location: Middleburg
Posts: 1,019
Quote:
Originally Posted by Jim1611 View Post
It's some of the more resonably priced in the state. The land east of there will get high, ie river bottom farm ground, and west of there I think it gets a bit cheaper. The general vicinity of it is rolling pasture and farm land. Some of the ground gets pretty rough too and it's only suitable for livestock grazing. What it doesn't have is the tourist attraction that the Ozark area and Branson has. They are pretty pricy. I haven't heard lately but in the past that part of the state was one of the few places land was still selling in the $1000.00 an acre range. Who knows Scott with a depressed economy there may be some bargains. Let me do some snoopin next week.
I got some land in Missouri... $1000 an acre haha. Try $10,000+ an acre here!

'83 CJ7 258I6 4-Speed Father Daughter Project - Using Monstaliner/Chassis Saver and Products from CrabTreeTool
NorthEastFL4x4.com - Local 4x4 Enthusiasts website, join up now!
FamillyCJ7 is offline  
post #334 of 5422 Old 08-28-2010, 10:35 PM Thread Starter
Skerr
Registered User
1985 CJ7 
 
Join Date: Sep 2008
Location: White Springs
Posts: 9,495
Quote:
Originally Posted by Jim1611 View Post
It's some of the more resonably priced in the state. The land east of there will get high, ie river bottom farm ground, and west of there I think it gets a bit cheaper. The general vicinity of it is rolling pasture and farm land. Some of the ground gets pretty rough too and it's only suitable for livestock grazing. What it doesn't have is the tourist attraction that the Ozark area and Branson has. They are pretty pricy. I haven't heard lately but in the past that part of the state was one of the few places land was still selling in the $1000.00 an acre range. Who knows Scott with a depressed economy there may be some bargains. Let me do some snoopin next week.
Thanks, Jim. Find me 80-100 acres with woods and hunting. Better find me a job too!

Kerrdog
Go Fish! <*////><

But the right word at the right time... "Hey, give me a little hug!" That's the difference between lightning and a harmless lightning bug!
Skerr is offline  
post #335 of 5422 Old 08-28-2010, 10:41 PM Thread Starter
Skerr
Registered User
1985 CJ7 
 
Join Date: Sep 2008
Location: White Springs
Posts: 9,495
SCORED!

Just bought a complete Bestop Supertop with doors and all hardware including frame (no holes or tears, windows clear), complete heater box assy (needs work), speedo, wiring harness, spring plates (Clay's spring plates have issues), bags of nuts, bolts, etc from a very nice guy up in Ohio. Thanks "Ohio Mike" for working so hard to get this stuff to me, and Thanks to my BIL, who went out of his way to secure it for me. Clay is like, "Ho Hum", and I'm about to BUST! Should have it here in FL by Thanksgiving when the family gets together.

Kerrdog
Go Fish! <*////><

But the right word at the right time... "Hey, give me a little hug!" That's the difference between lightning and a harmless lightning bug!
Skerr is offline  
post #336 of 5422 Old 08-29-2010, 01:41 PM
Jim1611
Web Wheeler
 
Jim1611's Avatar
1985 CJ7 
 
Join Date: Jul 2009
Posts: 7,190
Good news. Maybe Clay didn't get the excited Jeep parts thing in his genes from you Scott. My wife doesn't get too excited about things like Jeep parts either. Oh she tried to act that way, just being a good wife, But I can tell that she just doesn't lay in bed at night thinking about Jeep rides, having that big buck tied to the front bumper or any of the things that we all think of. They juat aren't as blessed as we are.

80-100 acres and hunting and a job. Hey I am on the lookout. You bet if I see anything you'll be getting contacted!! Trust me you will.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
(Crabtree Shackle Hangers)

My build thread

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Last edited by Jim1611; 08-29-2010 at 08:52 PM.
Jim1611 is offline  
post #337 of 5422 Old 08-29-2010, 08:50 PM
243
Registered User
1978 FSJ Cherokee 
 
Join Date: Sep 2002
Posts: 3,441
Quote:
Originally Posted by Skerr View Post
SCORED!

Just bought a complete Bestop Supertop with doors and all hardware including frame (no holes or tears, windows clear), complete heater box assy (needs work), speedo, wiring harness, spring plates (Clay's spring plates have issues), bags of nuts, bolts, etc from a very nice guy up in Ohio. Thanks "Ohio Mike" for working so hard to get this stuff to me, and Thanks to my BIL, who went out of his way to secure it for me. Clay is like, "Ho Hum", and I'm about to BUST! Should have it here in FL by Thanksgiving when the family gets together.

Sounds like a great haul

Dave's 78 Build
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
243 is offline  
post #338 of 5422 Old 08-29-2010, 10:13 PM Thread Starter
Skerr
Registered User
1985 CJ7 
 
Join Date: Sep 2008
Location: White Springs
Posts: 9,495
Today was a mixed day! I wasn't feeling good and I laid out of church. I pretty much laid around the house, too, but a friend of mine needed some help with a tractor, so he called me, and of course, I went. It's an old International and it's covered in gear oil... I wasn't planning on getting dirty. Didn't DRESS for it! But I got dirty. We also fixed his tractor. In exchange for help he let me pilfer his scrap metal pile. Now I had TRIED to build a torque arm out of a couple lawn mower blades on Saturday... but that didn't work. The steel is too hard and I couldn't drill it... burned up a couple of drill bits! So I had definite ideas about what I wanted to find in his scrap pile. I found some 3/8 stock that I thought would work great. He also loaned me a 7/8" drill bit. So I thought I would do a thread on building and setting up a torque arm. I was feeling better by now and I couldn't wait to get home. Things started out alright but quickly bombed! I burnt up a couple MORE drill bits and never DID get holes through the steel. About that time AJ shows up to check on our progress... he likes what he sees, but he can't stand the terrible screeching coming from the drill press! So he gets me lined out correctly, AFTER he sharpened/conditioned the damged drill bits and after he replaced the belt on my drill press. AJ made 5 trips to his house to get me things, like the belt, some bolts, and oh yeah... a piece of steel. Seems the piece I had gotten was hardened. Well, you can't tell by looking at it! At least I can't!! AJ spent a great deal of time with me this afternoon helping set up the torque arm. It's clear now that even had I managed to get the holes in MY piece of steel, I would have messed it up, because I did not think to bolt the tranny in place before I measured for the bushing. Fortunately, AJ rescued me from an otherwise counter-productive day. So here are some pics of our progress. BTW- I bagged the torque arm build idea!
Attached Thumbnails
IMG_3398_1.JPG   IMG_3400_1.JPG   IMG_3399_1.JPG   IMG_3403_1.JPG   IMG_3407_1.JPG  


Kerrdog
Go Fish! <*////><

But the right word at the right time... "Hey, give me a little hug!" That's the difference between lightning and a harmless lightning bug!

Last edited by Skerr; 08-29-2010 at 10:16 PM. Reason: grammar
Skerr is offline  
post #339 of 5422 Old 08-29-2010, 10:26 PM Thread Starter
Skerr
Registered User
1985 CJ7 
 
Join Date: Sep 2008
Location: White Springs
Posts: 9,495
Clay is active in church so he was gone for half the day, and he is also taking college courses, so he had homework. He did mange to get out of the house for a bit and coated his steering box with rust converter. He primed it and plans to paint it silver. He thinks it will be a nice contrast to the black frame! We'll see...


I set the original driveshaft in place just to see what it would look like. This is the driveshaft that came on the Jeep. The angle is outrageous! Since we removed the PO's original home-made lift I didn't think I would have DS issues. I set my 7 up with a 2.5" lift and liked it well enough to put the same lift on Clay's Jeep. I didn't have to make any mods to my 7 at all. I was expecting the same thing on Clay's 5. Obvously that is not the case. I suppose it's because of the shorter wheel base?? What are ya'll's suggestions? Angle the pinion up? Drop the tranny? Both??
Attached Thumbnails
IMG_3402_1.JPG   IMG_3410_1.JPG  

Kerrdog
Go Fish! <*////><

But the right word at the right time... "Hey, give me a little hug!" That's the difference between lightning and a harmless lightning bug!
Skerr is offline  
post #340 of 5422 Old 08-30-2010, 07:45 AM
Jim1611
Web Wheeler
 
Jim1611's Avatar
1985 CJ7 
 
Join Date: Jul 2009
Posts: 7,190
Hey Scott if you move away from there you're going to miss AJ, he sounds like a great friend and neighbor! That looks like a torgue arm anybody would be proud to have. If you ever need to drill a hole in hardened material, you can tell if it's hardened by trying to cut it on the edge with a file. A file will not touch anything about about 50 rockwell and anything above 40 rockwell is going to be tough to drill with high speed bits. Anyway you can drill through the hard stuff with carbide tipped masonary bits. Just make sure and have everything clamped good and tight and that when the drill breaks through the back side you let it cut through smooth. Carbide will hold up pretty good but what your drilling needs to stay put.

Scott if you shim the rear pinion to help with the driveshaft angle you need to keep it and the yoke angle on the transfer case as close to the same angle as you can, that's supposed to work best with the single u-joint set-up. You may need a duoble cardan u-joint back there. With them the angle needs to be offset about 2 degree. Any measuring you do on angles though needs to wait til after the Jeep is pretty well assembled. You may find by then that driveshaft angle isn't as bad as it is now.

Glad you're feeling better too!!


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
(Crabtree Shackle Hangers)

My build thread

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Jim1611 is offline  
post #341 of 5422 Old 08-30-2010, 08:31 PM Thread Starter
Skerr
Registered User
1985 CJ7 
 
Join Date: Sep 2008
Location: White Springs
Posts: 9,495
Quote:
Originally Posted by Jim1611 View Post
Hey Scott if you move away from there you're going to miss AJ, he sounds like a great friend and neighbor! That looks like a torgue arm anybody would be proud to have. If you ever need to drill a hole in hardened material, you can tell if it's hardened by trying to cut it on the edge with a file. A file will not touch anything about about 50 rockwell and anything above 40 rockwell is going to be tough to drill with high speed bits. Anyway you can drill through the hard stuff with carbide tipped masonary bits. Just make sure and have everything clamped good and tight and that when the drill breaks through the back side you let it cut through smooth. Carbide will hold up pretty good but what your drilling needs to stay put.

Scott if you shim the rear pinion to help with the driveshaft angle you need to keep it and the yoke angle on the transfer case as close to the same angle as you can, that's supposed to work best with the single u-joint set-up. You may need a duoble cardan u-joint back there. With them the angle needs to be offset about 2 degree. Any measuring you do on angles though needs to wait til after the Jeep is pretty well assembled. You may find by then that driveshaft angle isn't as bad as it is now.

Glad you're feeling better too!!
Thanks, Jim. Yeah... AJ has been a very good friend. Thanks for the info on cutting/drilling hardened steel. I didn't have a masonry bit that size.

I have a double-cardan DS for Clay's Jeep. I bought it many months ago and set it on the shelf. It seems to me now, after mocking up the DC DS, that it, too, will be too long! I won't worry about it for now, as you suggest. Just wanted to get it done. I think we'll concentrate on brakes. I gotta try and remember how the front discs go back to gether. I took the CJ5 discs and knuckles from the NT axle and installed them on the WT axle. I'm not sure I have everything. Gonna have to sit down with Mr. Chilton!

Kerrdog
Go Fish! <*////><

But the right word at the right time... "Hey, give me a little hug!" That's the difference between lightning and a harmless lightning bug!
Skerr is offline  
post #342 of 5422 Old 08-30-2010, 11:53 PM
rixcj
Web Wheeler
 
rixcj's Avatar
1979 CJ5 
 
Join Date: Jun 2007
Location: Saunderstown
Posts: 2,294
Quote:
Originally Posted by Skerr View Post

I think we'll concentrate on brakes. I gotta try and remember how the front discs go back to gether. I took the CJ5 discs and knuckles from the NT axle and installed them on the WT axle. I'm not sure I have everything. Gonna have to sit down with Mr. Chilton!
Hey, Scott...here's a thread that I posted a while back. It has some pretty good photos of the knuckles and brake components. Maybe they'll be of some help to you. Just remember, though, that my axle is in the vise backward (pumpkin offset to the opposite side), so the calipers appear upside down!

http://www.jeepforum.com/forum/f8/on...a-30-a-913012/

Rich

'79 CJ5, AMC 360, t-18/d20 twin stick, dana 30/amc20(Mosers), Edelbrock Performer intake, Holley 600, ps/pb, DUI HEI, 'glass tub/1pc. tilt nose, 33x12.50 BFG AT's.

There's a fine line between "hobby" and "mental illness".
rixcj is offline  
post #343 of 5422 Old 09-05-2010, 09:22 AM Thread Starter
Skerr
Registered User
1985 CJ7 
 
Join Date: Sep 2008
Location: White Springs
Posts: 9,495
Quote:
Originally Posted by Jim1611 View Post
Scott if you shim the rear pinion to help with the driveshaft angle you need to keep it and the yoke angle on the transfer case as close to the same angle as you can, that's supposed to work best with the single u-joint set-up. You may need a duoble cardan u-joint back there. With them the angle needs to be offset about 2 degree. Any measuring you do on angles though needs to wait til after the Jeep is pretty well assembled. You may find by then that driveshaft angle isn't as bad as it is now.

Glad you're feeling better too!!
Thanks, Jim... I will drop the tranny some and rotate the pinion some, see what happens. I have some shims around here somewhere.

Quote:
Originally Posted by rixcj View Post
Hey, Scott...here's a thread that I posted a while back. It has some pretty good photos of the knuckles and brake components. Maybe they'll be of some help to you. Just remember, though, that my axle is in the vise backward (pumpkin offset to the opposite side), so the calipers appear upside down!

http://www.jeepforum.com/forum/f8/on...a-30-a-913012/

Rich
Beautiful work, Rich. You are an artist! The pics do help... I discovered that I have Scout calipers, and I thought they were my CJ5 calipers. I couldn't make 'em go on for nothin'! (The Scout parts (the very few there are) came with the WT axle when I bought it. If anyone wants to see pics of what I have, let me know.)


I got it figured out. Clay cleaned up the hubs, etc, rust converted everything, and painted. Should have the front wheels back on by late afternoon. In the meantime, here are a couple of pics of Clay.

I hope everyone stays safe this weekend. Have a designated driver. Have a great Labor Day weekend. Time for some ribs on the grill!
Attached Thumbnails
IMG_3411_1.JPG   IMG_3412_1.JPG  

Kerrdog
Go Fish! <*////><

But the right word at the right time... "Hey, give me a little hug!" That's the difference between lightning and a harmless lightning bug!
Skerr is offline  
post #344 of 5422 Old 09-05-2010, 05:46 PM
Jim1611
Web Wheeler
 
Jim1611's Avatar
1985 CJ7 
 
Join Date: Jul 2009
Posts: 7,190
Glad to see you guys back at it!! Enjoy the ribs too.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
(Crabtree Shackle Hangers)

My build thread

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Jim1611 is offline  
post #345 of 5422 Old 09-05-2010, 06:22 PM Thread Starter
Skerr
Registered User
1985 CJ7 
 
Join Date: Sep 2008
Location: White Springs
Posts: 9,495
Quote:
Originally Posted by Jim1611 View Post
Glad to see you guys back at it!! Enjoy the ribs too.
Ugh! I don't think I EVER want to see anything made of Pork again!

We (I) had to take a Jeep break! But we're plinking away at some of the small stuff. Gotta cut off the factory shock mounts yet. Clay says we have to drop the axle to do it, but I'm not looking to do that (I don't WANT to do that) again. Trying to get the brake lines reconnected, which is proving to be more aggravating than I expected. And the Gnats are worse than I have seen in several years... you don't even want to go outside.

It could be worse....

Here is a pic of Clay's hub/brake setup. It looks alright. There isn't much to see once the wheel is back on.

Also, a pic of the Scout brake parts. PM me if anyone needs them.
Attached Thumbnails
IMG_3414_1.JPG   IMG_3415_1.JPG  

Kerrdog
Go Fish! <*////><

But the right word at the right time... "Hey, give me a little hug!" That's the difference between lightning and a harmless lightning bug!
Skerr is offline  
Reply

Tags
1979 , cj5 , fiberglass , rollcage , tailgate

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the JeepForum.com forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid e-mail address for yourself.



Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.




Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Similar Threads
Thread Thread Starter Jeep Forums Replies Last Post
19?? CJ7 build thread biker250 Jeep CJ Forum 96 12-27-2010 07:10 AM
Looking for a CJ Build Thread. jsc7002 Jeep CJ Forum 6 08-22-2009 11:47 AM
High 5 Build Thread... 1Rustycj5 Jeep CJ Forum 7 03-22-2009 10:28 PM
Build Thread for my '84 CJ erik5387 Jeep CJ Forum 19 05-29-2008 02:05 PM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome