JeepForum.com

JeepForum.com (http://www.jeepforum.com/forum/)
-   ZJ Grand Cherokee Forum (http://www.jeepforum.com/forum/f13/)
-   -   Zj arb bumper picture request (http://www.jeepforum.com/forum/f13/zj-arb-bumper-picture-request-1548916/)

Y0ungGunZJ 07-14-2013 04:04 PM

Zj arb bumper picture request
 
Yes I know I can google zj arb bumper. But what I need is the corners of the bumpers with some measurements if someone with an arb on their zj wouldnt mind taking some measurements.

Or I may try to do it my way and not do their weird angles. I need some good close ups though.

Currently my arb looks like this
http://i996.photobucket.com/albums/a...sf281eaef.jpeg

Texas ZJ1 07-14-2013 07:40 PM

I cut mine and moved the cut off piece forward to keep from having a sharp edge slicing up my tires.

Hunter

http://www.jeepforum.com/gallery/data/4/DSC01806.JPG

WhiteOut 07-14-2013 09:17 PM

Hope these help a bit.

http://i220.photobucket.com/albums/d...ps83b9581c.jpg

http://i220.photobucket.com/albums/d...ps7386c144.jpg

To the very front of the bumper
http://i220.photobucket.com/albums/d...psf330ce60.jpg

From the back of the tube
http://i220.photobucket.com/albums/d...ps96c6e2a9.jpg

http://i220.photobucket.com/albums/d...ps7357f62a.jpg

Y0ungGunZJ 07-14-2013 10:30 PM

Perfect! I think for mine I am going to stop it at the first flat part of the fender. And have it taper down to a 4" piece, I will make a templet tomorrow to show you guys roughly what it would look like in the end. I thought about running it all the way but I may move my axle forward a little, once I get some adj uppers and I check my clearance at full bump.

WhiteOut 07-14-2013 10:31 PM

Grab a front shot of your Jeep, it looks like your bumper is bent up a bit.

Y0ungGunZJ 07-14-2013 10:39 PM

The way its mounted its cocked a little so I have to clear out the slots a little. I up drilled the holes to 1/2 because I already had another bumper I was working on from an xj but looked like crap so I got the arb off cl and that guy had the arb on an xj. I think the holes on the bumper were a 1/2 inch equivalent.

Here is some front shots
http://i996.photobucket.com/albums/a...sb1ea706a.jpeg
http://i996.photobucket.com/albums/a...s20bbc67d.jpeg

WhiteOut 07-14-2013 10:41 PM

ARB will sell the replacement mounts by themselves for cheap.

Y0ungGunZJ 07-14-2013 10:49 PM

There is nothing wrong with them its just how the slots where I drilled cocked it a littke so the whole slot isnt 1/2 and I removed the over ends of the front crossmember zo I have to make some brackets for those angled mounting points.

Everything is sanwiched I have 3/16 plate in the unibody about a foot inside it, and I tied it with the other 2 holes that arb doesn't use.

Y0ungGunZJ 07-15-2013 08:55 PM

alright i made a rough cutout of what i am thinking of doing. thoughts comments concerns?


before: (the good side)
http://i996.photobucket.com/albums/a...ps48dad431.jpg
http://i996.photobucket.com/albums/a...ps99d14419.jpg

what i am thinking of doing (the main section there would be at the pencil line not that whole thing.)
http://i996.photobucket.com/albums/a...ps4481d835.jpg
http://i996.photobucket.com/albums/a...ps2b93b12f.jpg


The time now is 10:16 AM.

Powered by vBulletin Version 3.8.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.